Furnace Replacement cost: Edmonds vs Spokane (2026)
The two metros aren't quite in sync on furnace replacement: Edmonds sits 17% above Spokane, or roughly $6,700 versus $5,750 — about $950 apart.
Edmonds WA
Typically around $6,700
Spokane WA
Lower costTypically around $5,750
Edmonds vs Spokane: full breakdown
| Factor | Edmonds | Spokane |
|---|---|---|
| Typical 2026 cost | $6,700 | $5,750 |
| Estimated range | $4,800–$8,600 | $4,100–$7,350 |
| Labor index (vs US) | ×1.19 | ×1.02 |
| Climate zone | Mixed | Mixed |
| Climate factor | ×1 | ×1 |
| Local permit | $250 | $225 |
| Labor share | $4,000 | $3,450 |
| Materials/equipment | $2,700 | $2,300 |
Localized 2026 planning estimates — not quotes. Each city adjusts the national furnace replacement range for local labor, climate and permits.
Is the gap worth worrying about?
A 17% gap is meaningful on a project this size — about $950. That's real money, but it's often within reach of off-season timing and a tighter apples-to-apples bid in Edmonds.
Furnace replacement by type: Edmonds vs Spokane
Below, each furnace replacement option is priced independently for both cities, with identical local labor, climate and permit logic applied — so the comparison holds up.
| Type | Edmonds | Spokane |
|---|---|---|
| Gas furnace | $4,650–$8,450 | $4,000–$7,250 |
| High-efficiency gas furnace | $4,200–$8,450 | $3,600–$7,250 |
| Electric furnace | $2,650–$5,600 | $2,250–$4,800 |
Localized 2026 planning estimates — not quotes. Each city adjusts the national furnace replacement range for local labor, climate and permits.
Furnace replacement by home size: Edmonds vs Spokane
Furnace cost scales with the heating capacity (BTU) your home needs — roughly 40–45 BTU per square foot in a mixed climate. Larger homes need a bigger unit and more ductwork.
| Size | Edmonds | Spokane |
|---|---|---|
| 1,000 sq ft (≈45,000 BTU) | $3,600–$6,450 | $3,100–$5,500 |
| 1,500 sq ft (≈68,000 BTU) | $4,200–$7,400 | $3,600–$6,350 |
| 2,000 sq ft (≈90,000 BTU) | $4,800–$8,600 | $4,100–$7,350 |
| 2,500 sq ft (≈110,000 BTU) | $5,500–$9,800 | $4,700–$8,350 |
| 3,000 sq ft (≈130,000 BTU) | $6,200–$10,950 | $5,300–$9,400 |
| 3,500+ sq ft (≈150,000 BTU) | $6,900–$12,150 | $5,950–$10,400 |
Treat these as 2026 localized estimates for furnace replacement, not quotes from a contractor.
What hvac pros earn in each metro
Since labor accounts for around 60% of what a furnace replacement job costs, it's the biggest lever behind any price gap between cities. What you're seeing below is actual BLS metro wage data for skilled installers — not a guess.
Seattle-Tacoma-Bellevue metro · about 32% above the US average installer wage.
No BLS metro wage series for Spokane; we use Washington regional price parity instead.
Source: U.S. Bureau of Labor Statistics, OEWS metro wages for HVAC installers (used as a trade-labor index).
Cheapest time for furnace replacement in either city
HVAC demand collapses in the mild shoulder seasons, so installers discount to keep crews busy. The most expensive time to buy is during a heat wave or cold snap, when a dead system forces a full-price emergency replacement.
How much should you really budget for HVAC in 2026?
An HVAC budget isn't one number — it's a set of trade-offs between sizing accuracy, efficiency tier and brand. Our editors walk through how each one moves the price.
The longevity case
Brand is a footnote; sizing and install quality write the story. A right-sized mid-tier system that's properly commissioned and serviced once a year will outlive an oversized premium unit that short-cycles itself to an early grave. Put the money into the crew and the setup rather than the nameplate.
The budget-first case
In a temperate region the smart move is to size the job correctly with a Manual J and take the base efficiency tier. A system that spends most days coasting can't recover the cost of a high-SEER2 compressor, because the savings only show up under heavy load you don't put on it. Match the equipment to how little you actually run it, not to the brochure's top number.
The efficiency-first case
In a hot-summer or cold-winter region, a higher SEER2/AFUE unit — or a heat pump — earns its premium back in lower bills, and utility and state rebates can still cut into the sticker (the federal 25C/25D credits ended Dec 2025). Run the payback math before defaulting to the cheapest box.
Climate decides the efficiency tier; a proper load calculation decides everything else. Nail both, stack the rebates you can, and you've sidestepped the two mistakes — wrong size, rushed install — that actually inflate the lifetime cost.
Edmonds vs Spokane
Is furnace replacement cheaper in Edmonds or Spokane?
In 2026, furnace replacement is cheaper in Spokane at about $5,750, versus $6,700 in Edmonds — a difference of about $950 (17%).
Why does furnace replacement cost more in Edmonds than Spokane?
Edmonds's higher labor index (1.19 vs 1.02 in Spokane) is the biggest factor, with the mixed/mixed climate split and permit fee differences playing a smaller role.
How much is furnace replacement in Edmonds, WA?
Edmonds homeowners can expect $4,800 to $8,600 for furnace replacement in 2026, with $6,700 the typical number.
When is the cheapest time to buy furnace replacement — and does it differ by city?
It doesn't vary by location — Spring and fall (Mar–May, Sep–Oct) is the discount window in both Edmonds and Spokane (roughly 5–15% off), while peak summer and mid-winter tends to be the most expensive in either city.
Should I choose where to live based on furnace replacement cost?
Not really — the $950 gap is one-time, and smart timing and tighter quotes in Edmonds can shrink it. Factors that compound over time, like energy prices and home condition, deserve more weight than a single upfront difference.
Compare furnace replacement in other cities
Updated June 2026 · By Serhat Özçelik