Metal Roof Installation cost: Jacksonville vs Palm Bay (2026)
The two metros aren't quite in sync on metal roof installation: Jacksonville sits 5% below Palm Bay, or roughly $21,200 versus $22,300 — about $1,100 apart.
Jacksonville FL
Lower costTypically around $21,200
Palm Bay FL
Typically around $22,300
Jacksonville vs Palm Bay: full breakdown
| Factor | Jacksonville | Palm Bay |
|---|---|---|
| Typical 2026 cost | $21,200 | $22,300 |
| Estimated range | $12,950–$29,450 | $13,600–$31,000 |
| Labor index (vs US) | ×0.94 | ×0.99 |
| Climate zone | Hot | Hot |
| Climate factor | ×1.03 | ×1.03 |
| Local permit | $275 | $275 |
| Labor share | $12,700 | $13,400 |
| Materials/equipment | $8,500 | $8,900 |
Treat these as 2026 localized estimates for metal roof installation, not quotes from a contractor.
Is the gap worth worrying about?
That 5% gap is small — for metal roof installation it's usually less than the spread between two local contractors' quotes, so the metro matters far less than who you hire and when you buy.
Metal roof installation by type: Jacksonville vs Palm Bay
Every metal roof installation type gets its own localized price for each metro, using the same labor, climate and permit adjustments — a true apples-to-apples comparison.
| Type | Jacksonville | Palm Bay |
|---|---|---|
| Corrugated steel (exposed fastener) | $9,050–$17,800 | $9,500–$18,700 |
| Standing-seam steel | $17,800–$34,350 | $18,700–$36,100 |
| Aluminum | $13,900–$27,500 | $14,600–$28,950 |
| Copper | $29,450–$58,650 | $31,000–$61,700 |
| Zinc | $27,500–$53,800 | $28,950–$56,600 |
All figures are 2026 localized planning estimates for metal roof installation — get an actual quote before you commit.
Metal roof installation by roof size: Jacksonville vs Palm Bay
Metal roofing is priced per square (100 sq ft) and costs roughly $6–$14 per sq ft installed — two to three times asphalt, but it lasts decades longer. Standing-seam costs more than exposed-fastener panels.
| Size | Jacksonville | Palm Bay |
|---|---|---|
| 1,000 sq ft (10 squares) | $8,050–$15,850 | $8,450–$16,650 |
| 1,500 sq ft (15 squares) | $11,000–$22,650 | $11,550–$23,800 |
| 2,000 sq ft (20 squares) | $12,950–$29,450 | $13,600–$31,000 |
| 2,500 sq ft (25 squares) | $15,850–$35,300 | $16,650–$37,150 |
| 3,000+ sq ft (30 squares) | $18,750–$41,150 | $19,750–$43,300 |
All figures are 2026 localized planning estimates for metal roof installation — get an actual quote before you commit.
What roofing pros earn in each metro
Labor is about 60% of a metal roof installation bill, so local wages drive most of the gap. These are real metro hourly wages for skilled installers (BLS OEWS), not estimates.
Jacksonville metro · about 9% below the US average installer wage.
No BLS metro wage series for Palm Bay; we use Florida regional price parity instead.
Source: U.S. Bureau of Labor Statistics, OEWS metro wages for HVAC installers (used as a trade-labor index).
Cheapest time for metal roof installation in either city
Shingles seal properly only in warm, dry conditions, which is exactly when everyone else wants a new roof too — especially right after a summer hailstorm. Lock in a late-fall or winter booking for a spring install and you skip that rush.
Where does a smart roofing budget go in 2026?
Tear-off vs. overlay, shingle tier and what's hidden under the deck decide the real number. Our editors on the trade-offs.
The value case
Architectural shingles sit between bargain 3-tab and premium metal or tile, and for most houses that middle ground is exactly right. They carry longer wind and wear ratings than 3-tab for a small step up in price, without the four-figure jump metal or tile demands.
The risk case
Budget for the unknown: rotten decking found at tear-off is the most common surprise. Get the per-sheet repair rate in writing up front so a "cheap" bid doesn't balloon mid-job.
The do-it-right case
Skipping the tear-off means burying whatever's failing underneath, and a second layer bakes the shingles from below until they curl early. Doing it properly means stripping to the deck, then paying for real underlayment, flashing and airflow — the work that sets how long the roof lasts, not just how it looks the first week.
Judge a roofing bid on its scope, not its bottom line — a genuine tear-off, a documented per-sheet deck rate, and a mid-grade architectural shingle. Those three close the gaps that let a low storm-season number balloon over the years.
Jacksonville vs Palm Bay
Is metal roof installation cheaper in Jacksonville or Palm Bay?
Jacksonville wins on price: metal roof installation runs about $21,200 there versus $22,300 in Palm Bay, a gap of roughly $1,100 (5%) as of 2026.
Why does metal roof installation cost more in Palm Bay than Jacksonville?
Labor rates explain most of it — 0.99 in Palm Bay vs 0.94 in Jacksonville. A hot climate versus hot accounts for the rest.
How much is metal roof installation in Jacksonville, FL?
Expect to pay $12,950 to $29,450 for metal roof installation in Jacksonville in 2026, averaging around $21,200.
When is the cheapest time to buy metal roof installation — and does it differ by city?
Timing doesn't change by city here — Late spring to early fall (dry, 45–85°F) is the cheapest window in both Jacksonville and Palm Bay, saving roughly 5–10%. Avoid mid-winter and the post-storm rush in either location, when emergency replacements push prices up.
Should I choose where to live based on metal roof installation cost?
That would be a stretch. $1,100 is a one-time difference, not an ongoing one, and off-season buying plus apples-to-apples bids in Palm Bay can close a good chunk of it. What matters more long-term is energy costs, climate and the condition of the home.
Compare metal roof installation in other cities
Updated June 2026 · By Serhat Özçelik