Metal Roof Installation cost: Arlington Heights vs Chicago (2026)
Metal roof installation costs about the same in Arlington Heights and Chicago in 2026 — roughly $25,700 in each.
Arlington Heights IL
Typically around $25,700
Chicago IL
Typically around $25,700
Arlington Heights vs Chicago: full breakdown
| Factor | Arlington Heights | Chicago |
|---|---|---|
| Typical 2026 cost | $25,700 | $25,700 |
| Estimated range | $15,650–$35,700 | $15,650–$35,700 |
| Labor index (vs US) | ×1.14 | ×1.14 |
| Climate zone | Cold | Cold |
| Climate factor | ×1.04 | ×1.04 |
| Local permit | $300 | $300 |
| Labor share | $15,400 | $15,400 |
| Materials/equipment | $10,300 | $10,300 |
Localized 2026 planning estimates — not quotes. Each city adjusts the national metal roof installation range for local labor, climate and permits.
A wash — choose on quality, not city
The two metros are effectively a wash for metal roof installation — pick on contractor quality and timing, not location.
Metal roof installation by type: Arlington Heights vs Chicago
We localize each metal roof installation type separately for both metros, applying the same labor, climate and permit adjustments each time, so you're comparing like for like.
| Type | Arlington Heights | Chicago |
|---|---|---|
| Corrugated steel (exposed fastener) | $10,900–$21,550 | $10,900–$21,550 |
| Standing-seam steel | $21,550–$41,600 | $21,550–$41,600 |
| Aluminum | $16,850–$33,350 | $16,850–$33,350 |
| Copper | $35,700–$71,100 | $35,700–$71,100 |
| Zinc | $33,350–$65,200 | $33,350–$65,200 |
These are 2026 planning figures for metal roof installation, localized to each city — not formal quotes.
Metal roof installation by roof size: Arlington Heights vs Chicago
Metal roofing is priced per square (100 sq ft) and costs roughly $6–$14 per sq ft installed — two to three times asphalt, but it lasts decades longer. Standing-seam costs more than exposed-fastener panels.
| Size | Arlington Heights | Chicago |
|---|---|---|
| 1,000 sq ft (10 squares) | $9,750–$19,200 | $9,750–$19,200 |
| 1,500 sq ft (15 squares) | $13,300–$27,450 | $13,300–$27,450 |
| 2,000 sq ft (20 squares) | $15,650–$35,700 | $15,650–$35,700 |
| 2,500 sq ft (25 squares) | $19,200–$42,800 | $19,200–$42,800 |
| 3,000+ sq ft (30 squares) | $22,750–$49,900 | $22,750–$49,900 |
Metal roof installation numbers here are 2026 planning ranges, adjusted per city — useful for budgeting, not a substitute for an actual quote.
What roofing pros earn in each metro
About 60% of a metal roof installation bill goes to labor, so wage differences between these two metros matter more than almost anything else. These are real, government-sourced (BLS OEWS) installer wages, not estimates.
Chicago-Naperville-Elgin metro · about 23% above the US average installer wage.
Chicago-Naperville-Elgin metro · about 23% above the US average installer wage.
Source: U.S. Bureau of Labor Statistics, OEWS metro wages for HVAC installers (used as a trade-labor index).
Cheapest time for metal roof installation in either city
Shingles seal properly only in warm, dry conditions, which is exactly when everyone else wants a new roof too — especially right after a summer hailstorm. Lock in a late-fall or winter booking for a spring install and you skip that rush.
Where does a smart roofing budget go in 2026?
A roofing quote can hide a lot behind a single number — whether it's a true tear-off, the shingle grade, and what's under the surface. Here's how our editors sort through it.
The value case
Architectural shingles sit between bargain 3-tab and premium metal or tile, and for most houses that middle ground is exactly right. They carry longer wind and wear ratings than 3-tab for a small step up in price, without the four-figure jump metal or tile demands.
The risk case
The surprise that wrecks a roofing budget is rot in the decking, and you rarely see it until the old shingles come off. Fix the price per replacement sheet in the contract before the crew starts, so a low bid can't quietly climb once the deck is open.
The do-it-right case
Pay for a full tear-off and quality underlayment, flashing and ventilation. An overlay saves money today but traps heat, voids some warranties and costs more at the next replacement.
Insist on tear-off over overlay, get the deck-repair rate in writing before work starts, and lean toward architectural shingles. Skipping any of the three tends to cost more later than it saves now.
Arlington Heights vs Chicago
Is metal roof installation cheaper in Arlington Heights or Chicago?
Practically identical — expect around $25,700 for metal roof installation whichever city you're in.
Why does metal roof installation cost more in Chicago than Arlington Heights?
It comes down to labor: Chicago indexes at 1.14 against Arlington Heights's 1.14. The cold-vs-cold climate difference adds to the gap.
How much is metal roof installation in Arlington Heights, IL?
In Arlington Heights, metal roof installation typically runs $15,650–$35,700 in 2026, with most homeowners paying around $25,700.
Do roofing pros really charge more in one city?
It's not a myth — BLS data puts installer wages at about $38.1/hr in the Chicago-Naperville-Elgin area and $38.1/hr in Chicago-Naperville-Elgin. Given labor is around 60% of a metal roof installation job's cost, that gap explains most of the price spread.
When is the cheapest time to buy metal roof installation — and does it differ by city?
It doesn't vary by location — Late spring to early fall (dry, 45–85°F) is the discount window in both Arlington Heights and Chicago (roughly 5–10% off), while mid-winter and the post-storm rush tends to be the most expensive in either city.
Should I choose where to live based on metal roof installation cost?
Cost shouldn't be the deciding factor between Arlington Heights and Chicago — they land at nearly the same price. Contractor reputation, scope, equipment tier and timing matter more.
Compare metal roof installation in other cities
Updated June 2026 · By Serhat Özçelik