Water Heaters · Murray, UT
How much does heat pump water heater installation cost in Murray, UT? (2026)
In Murray, heat pump water heater installation runs $2,450–$4,550, with most paying around $3,500 — about 4% above the national average. Installing a hybrid heat pump water heater — the most energy-efficient option, with the lowest operating cost.
Updated June 2026 · Localized estimate, not a quote
Most homeowners pay around $3,500
- Typical cost
- $3,500
- Labor vs US
- −4%
- Climate
- Cold
- Local permit
- $150
Refine your estimate
Tune it to your home to narrow the heat pump water heater installation range.
Key takeaways for Murray
- In Murray, heat pump water heater installation runs $2,450–$4,550 — call it $3,500 for a typical job, about 4% above the national average.
- This estimate departs from the national number mainly because Murray labor sits −4% versus the US average.
- The estimate already covers the Water Heaters permit — roughly $150 in Murray.
- Count on 13–15 years from a solid install; timing the next job yourself avoids the emergency premium.
- Time it right and you can save 5–10%: the best window to book is Spring and early fall.
- Don't price this without checking the rebates section below — federal 25C/25D credits and local utility incentives can bring the net cost down.
What goes into the price in Murray
A typical Murray heat pump water heater installation of $3,500 breaks down roughly like this — materials priced near the national level, labor set by local rates.
| Line item | Murray 2026 range |
|---|---|
| Materials & equipmentEquipment and supplies, which price out close to the national baseline. | $1,050 – $2,000 |
| Labor & installationThe installation work itself — removal, setup and startup — is what your city's labor rate actually moves. | $1,250 – $2,400 |
| Permit & feesWater Heaters permit cost, adjusted to this city's rate. | $150 |
| Total installed cost | $2,450 – $4,550 |
Split from the Murray estimate using a 55% local-labor share; line items sum to the total.
Why heat pump water heater installation costs what it does in Murray
- Labor in Murray runs about 4% below the national average (based on price levels for the Salt Lake City-Murray metro area), which lowers the installed price.
- The cold climate in Murray adds roughly 2% to typical heat pump water heater installation pricing versus a neutral climate.
- Murray's Water Heaters permit runs roughly $150, which is already part of the number above.
Heat Pump Water Heater Installation cost by tank capacity in Murray
Hybrid heat pump water heaters use a storage tank, so they're sized in gallons by household — but because they recover heat efficiently, a 50-gallon hybrid often serves a home that needed a 65–80 gallon electric tank.
| tank capacity | Murray 2026 range |
|---|---|
| 40 gal (1–2 people) | $2,250 – $3,750 |
| 50 gal (2–4 people) | $2,450 – $4,150 |
| 65 gal (4–5 people) | $2,850 – $4,350 |
| 80 gal (5+ people) | $3,150 – $4,550 |
National size ranges localized to Murray labor and climate.
Heat Pump Water Heater Installation cost by type in Murray
| 40–50 gallon | $2,450 – $3,950 |
| 65–66 gallon | $2,950 – $4,350 |
| 80 gallon | $3,450 – $5,050 |
Adjusted to Murray from national type-level ranges.
Labor vs. materials in Murray
Install crew, removal, permit & startup — the part Murray rates move most.
Equipment & materials — priced closer to the national level.
Split based on a typical $3,500 Murray project; your mix varies with scope.
Skilled installers in the Salt Lake City-Murray area earn about $30.1/hr (3% below the US average, per BLS metro wage data) — the local wage is what moves the labor half of your heat pump water heater installation cost.
How we estimate it
| National range | $2,300 – $4,400 |
| Murray labor adjustment | ×0.98 |
| cold climate factor | ×1.02 |
| Local permit | +$150 |
| Murray estimate | $2,450 – $4,550 |
Promo prices vs. the real cost
That advertised install price usually stops at the unit on the shelf — the permit, an expansion tank, updated venting and hauling off the old heater all land on the final invoice. Here's where the ad number and the real one part ways:
- "Free" estimate$0 — it's a sales visit
- "Basic swap" specialfrom ~$1,200 (simple tank)
- Service / diagnostic call$75–$150
Additional heat pump water heater installation costs to budget for
Expect a few of these rather than all. Which ones apply tracks with access, hidden damage and local code.
| Old heater removal & disposal | $50 – $200 |
| Electrical circuit / panel upgrade240V units need a dedicated circuit; older panels may need an upgrade | $300 – $2,000 |
| Condensate drain run | $100 – $400 |
| Expansion tank (often code-required) | $100 – $350 |
| Ducting / louvered door for adequate air volume | $150 – $600 |
Typical national add-on ranges; confirm locally during your quote.
What's included
- Removal of the old unit
- The hybrid heat pump water heater
- Labor and permit
- Electrical and condensate connections
What affects the cost
- Install location (needs adequate air volume)
- Condensate drainage routing
- Tank capacity and first-hour rating
- Electrical capacity and any panel upgrade
Ways to save on heat pump water heater installation in Murray
- Strong federal and state heat-pump incentives
- Lowest operating cost of any type — big lifetime savings
- Pair with time-of-use electricity rates
- Place in a warm space (garage, utility room) for efficiency
How long does heat pump water heater installation last in Murray?
Heat pump water heaters last about 13–15 years — longer than a standard tank — with the heat-pump components covered by warranty.
Flush the tank and clean the air filter and evaporator coil yearly so the heat pump keeps running efficiently.
Signs you need heat pump water heater installation in Murray
- Your electric tank is failing and you want to cut running costs
- Your water heating bills are high (a hybrid uses ~2–3x less energy)
- You're electrifying the home and away from gas
- You have a warm space (garage/basement) with room for the unit and its airflow
- An existing unit is 13+ years old
- You want the lowest operating cost and can tap local utility or state rebates
Repair or replace in Murray?
Repair if…
- The unit is under ~10 years old
- It's the backup heating element, fan, or a sensor
- The compressor is still under warranty
Replace if…
- The tank itself is leaking
- The compressor has failed and it's out of warranty
- It's 13+ years old and needs a major repair
Cost to run
Yearly running cost — what most cost guides skip
Install price is only half the story. Over 10 years, the fuel bill often outweighs the price difference between models. National operating-cost estimates below (FTC EnergyGuide):
| Type | Per year | 10-year fuel |
|---|---|---|
Heat pump water heaterCheapest to runThis page Cheapest to run — pulls heat from the air, ~3–4× more efficient than resistance. | $130 | $1,300 |
Gas tankless On-demand gas; no standby loss, so cheaper to run than a gas tank. | $270 | $2,700 |
Gas storage tank Low running cost where natural gas is cheap; some standby heat loss. | $330 | $3,300 |
Electric tankless On-demand electric; needs a heavy electrical service upgrade. | $500 | $5,000 |
Electric storage tank Cheapest to buy, most expensive to run at national electricity prices. | $570 | $5,700 |
Verified July 2026. Figures use FTC EnergyGuide / DOE (national average fuel prices) — your state's fuel prices move them: where electricity is cheap or gas is expensive the ranking shifts. Check current EIA residential energy prices for your state.
Rebates & tax credits
The federal 25C credit for heat-pump water heaters (up to $2,000) ended December 31, 2025 and is not available for 2026 installs. State and utility rebate programs may still cut the cost — check the DSIRE database, your state energy office, and your utility — and a heat-pump unit's very low running cost pays back over time.
Cheapest time for heat pump water heater installation in Murray
Tanks fail most in winter when incoming water is cold and demand is high — emergency-rate territory. Replacing a 10+ year-old unit proactively in a slow month avoids the premium.
Why heat pump water heater installation quotes vary — and how to compare them fairly
When two quotes for one project diverge by thousands, the cause is usually what each one includes, not markup — here's how to read the difference.
Why a quote looks high (or low)
- Tank vs. tankless is a different job — tankless often needs gas-line or electrical-panel upgrades.
- Fuel type and first-hour/GPM sizing change the equipment cost.
- Code work (expansion tank, venting, drain pan, straps) may be excluded from a low bid.
Get an apples-to-apples bid
- For tankless, ask if the gas line or electrical panel needs upgrading.
- Confirm old-unit removal and disposal are in the price.
- Decide tank vs. tankless first, then compare like models.
- Ask whether code upgrades (expansion tank, venting) are included.
Questions to ask Murray Water Heaters pros
The only honest way to compare is to hold every quote to one checklist. Start with these.
- 1Will the new unit meet current code (expansion tank, venting, seismic straps, drain pan)?
- 2Is removal and disposal of the old heater included in the price?
- 3For tankless: does my gas line or electrical panel need an upgrade?
- 4What's the first-hour rating / GPM, and is it sized for my household?
- 5What does the warranty cover, and who handles warranty service?
Heat Pump Water Heater Installation in Murray
How much does heat pump water heater installation cost in Murray, UT?
For Murray homeowners, heat pump water heater installation typically falls between $2,450 and $4,550 in 2026, averaging close to $3,500. The figure is adjusted for local labor rates, cold-climate factors and permit fees.
Is heat pump water heater installation more expensive in Murray than average?
Compared with the rest of the country, Murray runs about 4% higher than the national average — local labor prices at an index of 0.98 against the US average., plus a local Water Heaters permit running about $150.
Do I need a permit for heat pump water heater installation in Murray?
Expect to pull a Water Heaters permit in Murray — about $150 — which is already built into the estimate above, not an extra charge.
What affects heat pump water heater installation cost the most?
Installing a hybrid heat pump water heater — the most energy-efficient option, with the lowest operating cost. From there, a handful of specifics push the final number up or down. Your cold climate zone plays a part, but equipment/material grade, the size and complexity of the home, and local labor rates weigh in just as heavily.
Tank or tankless — and what should you budget?
The format choice drives both upfront cost and lifetime value. How our editors think about it.
The heat-pump case
A hybrid heat-pump unit carries the steepest sticker price and draws the largest utility rebates on the market, then pays that back by pulling warmth from the surrounding air instead of generating heat — operating cost falls to a fraction of a standard electric tank's. The condition is location: it wants a roomy, temperate spot like a garage or basement to perform.
The tankless case
Tankless costs more upfront and may need a gas-line or electrical upgrade, but it lasts longer, never runs out of hot water and trims standby energy loss — strongest for larger households planning to stay put.
The simple-swap case
When money is the constraint and the existing tank has kept up with the household, dropping in the same fuel type and capacity is the least disruptive move. No venting rework, no new gas line, no panel space to find — a plumber can pull the old unit and set the new one before lunch.
There's no universally "best" water heater — only the one that fits your budget and timeline. Tight budget, go tank; want endless hot water, go tankless; optimizing for the lowest bill, go heat-pump.
Editorial analysis by Serhat Özçelik, reviewed by Costadia Editorial. These are our own cost perspectives, not third-party endorsements.
How we calculated this estimate
We start with 2026 national heat pump water heater installation ranges compiled from contractor-pricing sources (Angi, HomeGuide, Fixr and EnergySage averages), then localize them to Murray using the BLS metro wage data labor index (×0.98 here), the IECC cold-climate factor (×1.02) and a typical local permit fee (≈$150). Federal incentive details reference the IRS Inflation Reduction Act (25C/25D) and DSIRE.
This is a planning estimate, not a quote.Actual prices vary with your home's condition, equipment grade and contractor — always confirm with licensed local pros before budgeting.
References & data sources
Our Murray heat pump water heater installation estimate is built from these primary, mostly government sources — not a single aggregator.
- Occupational Employment & Wage Statistics (metro wages) — U.S. Bureau of Labor Statistics.Metro-level trade wages behind each city's labor index.
- Regional Price Parities (state & metro) — U.S. Bureau of Economic Analysis.Regional price levels used where metro wage data is unavailable.
- IECC Climate Zones — U.S. DOE — Building Energy Codes Program.Climate-zone factors applied to weather-sensitive projects.
- Home Energy Tax Credits (25C / 25D) — Internal Revenue Service.Federal rebate and tax-credit figures for eligible upgrades.
- Database of State Incentives for Renewables & Efficiency — DSIRE — NC State University.State and utility incentive programs by ZIP code.
Heat pump water heater installation alternatives in Murray
Other projects in Murray
Browse local 2026 costs for every home project in Murray, UT.