Plumbing · Irving, TX
How much does whole-house repipe cost in Irving, TX? (2026)
In Irving, whole-house repipe runs $3,500–$7,950, with most paying around $5,750 — about 1% above the national average. Replacing a home's water supply piping — typically swapping old galvanized or failing pipe for PEX or copper.
Updated June 2026 · Localized estimate, not a quote
Most homeowners pay around $5,750
- Typical cost
- $5,750
- Labor vs US
- +3%
- Climate
- Hot
- Local permit
- $250
Refine your estimate
Tune it to your home to narrow the whole-house repipe range.
Key takeaways for Irving
- Expect $3,500 to $7,950 for whole-house repipe in Irving; most quotes cluster near $5,750, about 1% above the national average.
- The +3% gap between Irving and national labor rates is the single biggest reason this price isn't the national average.
- Set aside roughly $250 for the permit; that's already part of the range above, not an add-on.
- 50 to 100 years is the usual service life, so budget for the next one before it fails.
- Time it right and you can save Around 5%: the best window to book is Off-peak winter for planned work.
What goes into the price in Irving
A typical Irving whole-house repipe of $5,750 breaks down roughly like this — materials priced near the national level, labor set by local rates.
| Line item | Irving 2026 range |
|---|---|
| Materials & equipmentEquipment and supplies, which price out close to the national baseline. | $1,300 – $3,100 |
| Labor & installationInstall crew, removal and startup — the part local rates move most. | $1,950 – $4,600 |
| Permit & feesLocal building-department fee for Plumbing work here. | $250 |
| Total installed cost | $3,500 – $7,950 |
Split from the Irving estimate using a 60% local-labor share; line items sum to the total.
Why whole-house repipe costs what it does in Irving
- Irving's labor rates sit about 3% higher than the national average (based on price levels for the Dallas-Fort Worth-Arlington metro area), pushing the price up.
- Because Irving sits in a hot climate zone, whole-house repipe costs run about 1% lower than a neutral-climate baseline.
- Irving's Plumbing permit runs roughly $250, which is already part of the number above.
Whole House Repipe cost by home size in Irving
Repipe cost scales with how many bathrooms and fixtures the crew has to reach — more baths means more runs, more wall and ceiling access, and more labor. Pricing below assumes standard single-story access.
| home size | Irving 2026 range |
|---|---|
| 1 bath / ~1,000 sq ft | $3,150 – $5,550 |
| 2 bath / ~1,500 sq ft | $3,900 – $7,000 |
| 3 bath / ~2,000 sq ft | $4,850 – $8,900 |
| 4+ bath / 2,500+ sq ft | $6,000 – $11,800 |
National size ranges localized to Irving labor and climate.
Whole House Repipe cost by type in Irving
| PEX | $3,500 – $6,950 |
| CPVC | $4,100 – $7,950 |
| Copper | $6,000 – $14,650 |
Adjusted to Irving from national type-level ranges.
Whole House Repipe cost by efficiency in Irving
The pipe material drives both price and longevity. PEX is flexible, fast to run, and the cheapest to install; rigid copper costs more in material and labor but is the long-haul standard many buyers prefer.
| PEX (cross-linked polyethylene)Cheapest to install; flexible, freeze-tolerant | $3,150 – $6,000 |
| CPVCMid-cost rigid plastic; common in hot-water lines | $3,600 – $7,000 |
| Copper (rigid)Highest cost; long lifespan, resale appeal | $5,050 – $11,800 |
Labor vs. materials in Irving
Install crew, removal, permit & startup — the part Irving rates move most.
Equipment & materials — priced closer to the national level.
Split based on a typical $5,750 Irving project; your mix varies with scope.
Skilled installers in the Dallas-Fort Worth-Arlington area earn about $29.7/hr (5% below the US average, per BLS metro wage data) — the local wage is what moves the labor half of your whole-house repipe cost.
How we estimate it
| National range | $3,400 – $8,000 |
| Irving labor adjustment | ×0.97 |
| hot climate factor | ×0.99 |
| Local permit | +$250 |
| Irving estimate | $3,500 – $7,950 |
Promo prices vs. the real cost
A trip charge and a project estimate answer different questions — don't read one as a preview of the other:
- Service / diagnostic call$75–$200
- "Free" estimate on big jobs$0 — it's a sales visit
- Camera inspection$100–$350 (sometimes waived)
Additional whole-house repipe costs to budget for
Expect a few of these rather than all. Which ones apply tracks with access, hidden damage and local code.
| Drywall & wall/ceiling patch + repaintCrews open walls to reach pipes; finishing is often separate | $500 – $3,000 |
| Permit & inspection | $100 – $500 |
| Move out / hotel during workWhole-house repipes can take 2–5 days with water off | $0 – $1,000 |
| Replace shutoff valves & supply lines | $150 – $600 |
| Slab access / concrete cut (slab homes)Only if lines run under a concrete slab | $1,000 – $4,000 |
Typical national add-on ranges; confirm locally during your quote.
What's included
- Removal of accessible old piping
- Fixture reconnections
- New PEX or copper supply lines
- Basic drywall patching and permit
What affects the cost
- PEX vs copper
- Wall opening and patching needed
- Slab vs crawlspace/basement access
- Home size and number of bathrooms
Ways to save on whole-house repipe in Irving
- Repipe during a remodel to share wall access
- Get multiple licensed-plumber bids
- PEX costs less than copper and installs faster
- Act before a leak causes water damage
How long does whole-house repipe last in Irving?
PEX and CPVC last ~40–50+ years; copper commonly reaches 50–70+ years. A repipe is essentially a once-in-a-lifetime job.
Repiped supply lines need almost no upkeep; budget only for the occasional shutoff-valve or fixture check.
Signs you need whole-house repipe in Irving
- Chronic low water pressure throughout the house
- Rusty, brown, or metallic-tasting water (corroding pipes)
- Frequent or repeated pinhole leaks and pipe repairs
- Old galvanized steel, polybutylene, or lead supply pipes
- Banging, knocking, or whistling pipes (water hammer / corrosion)
- Visible corrosion, flaking, or green stains on exposed pipe
- The home is 50+ years old on its original plumbing
Repair or replace in Irving?
Repair if…
- A single, accessible leak in otherwise sound modern pipe (PEX/copper)
- The rest of the system is under ~25 years old and leak-free
- The damaged section is short and easy to isolate
Replace if…
- Pipes are galvanized steel, polybutylene, or lead
- Leaks keep recurring in different spots (systemic corrosion)
- Water pressure and water quality are both declining
- You're already gutting walls for a remodel (do it once)
Cheapest time for whole-house repipe in Irving
Emergency plumbing work is priced for urgency, full stop. A repipe or sewer line, on the other hand, is a project you can schedule — and scheduling it for a slow month gets you a slightly better rate and a crew that isn't rushing.
Why whole-house repipe quotes vary — and how to compare them fairly
One bid high, one low, same house? The variable is scope. Here's what pushes the figure up or down and how to get quotes you can actually compare.
Why a quote looks high (or low)
- Pipe material (PEX vs. copper) changes both cost and longevity.
- Trenchless vs. traditional dig is a major price difference.
- Permits, inspection and surface/landscape restoration may be excluded.
Get an apples-to-apples bid
- Ask whether trenchless or dig fits your situation and why.
- Clarify who owns the city-side portion of the line.
- Compare pipe material on equal terms.
- Confirm permits, inspection and restoration are included.
Questions to ask Irving Plumbing pros
Before you pick, make each contractor answer the same things — gaps in their replies tell you as much as the price.
- 1Trenchless vs. traditional dig — which fits my situation and why?
- 2Is a camera inspection included so we confirm the scope before digging?
- 3Are permits, inspection, and surface/landscape restoration included?
- 4What pipe material are you using (PEX vs. copper) and why?
- 5Who is responsible for the city-owned portion of the line?
Whole House Repipe in Irving
How much does whole-house repipe cost in Irving, TX?
In Irving, whole-house repipe typically costs $3,500 to $7,950 in 2026, with most homeowners paying around $5,750. Why that specific number? It reflects Irving labor rates, hot-climate demands and permit fees rather than a flat national figure.
Is whole-house repipe more expensive in Irving than average?
Compared with the rest of the country, Irving runs about 1% higher than the national average — local labor prices at an index of 0.97 against the US average.; add in a Plumbing permit at roughly $250.
Do I need a permit for whole-house repipe in Irving?
Most Irving jurisdictions require a Plumbing permit for this work. Budget roughly $250 for the permit; it is already included in the estimate above.
What affects whole-house repipe cost the most?
Here's the short version: replacing a home's water supply piping — typically swapping old galvanized or failing pipe for PEX or copper. What should you watch? Equipment or material grade, the home's size and complexity, local labor rates, and your hot climate zone — in roughly that order.
How do you budget a major plumbing job?
Plumbing budgets for repipes and sewer lines hinge on two unknowns — the install method and the ground itself. Our editors break down the trade-offs.
The method case
Trenchless runs a higher per-foot rate, but the savings hide in what you never have to rebuild — no torn-up driveway, no re-sodded lawn, no ripped-out patio. Open-cut digging only wins on price when there's almost nothing on top of the line to put back.
The diagnosis-first case
Never budget a sewer or repipe job from a guess. A camera inspection confirms the real scope and stops you paying for work you don't need — or being blindsided by work you do.
The material case
PEX is cheaper, faster and freeze-tolerant; copper costs more but lasts longer and some buyers prefer it. Match the material to your climate and how long you'll own the home.
Start with a camera inspection so the scope is fact, not a guess. Compare trenchless against the dig's full restoration bill, not just the excavation, and choose pipe material for your climate.
Editorial analysis by Serhat Özçelik, reviewed by Costadia Editorial. These are our own cost perspectives, not third-party endorsements.
How we calculated this estimate
We start with 2026 national whole-house repipe ranges compiled from contractor-pricing sources (Angi, HomeGuide, Fixr and EnergySage averages), then localize them to Irving using the BLS metro wage data labor index (×0.97 here), the IECC hot-climate factor (×0.99) and a typical local permit fee (≈$250). Federal incentive details reference the IRS Inflation Reduction Act (25C/25D) and DSIRE.
This is a planning estimate, not a quote.Actual prices vary with your home's condition, equipment grade and contractor — always confirm with licensed local pros before budgeting.
References & data sources
Our Irving whole-house repipe estimate is built from these primary, mostly government sources — not a single aggregator.
- Occupational Employment & Wage Statistics (metro wages) — U.S. Bureau of Labor Statistics.Metro-level trade wages behind each city's labor index.
- Regional Price Parities (state & metro) — U.S. Bureau of Economic Analysis.Regional price levels used where metro wage data is unavailable.
- IECC Climate Zones — U.S. DOE — Building Energy Codes Program.Climate-zone factors applied to weather-sensitive projects.
- Home Energy Tax Credits (25C / 25D) — Internal Revenue Service.Federal rebate and tax-credit figures for eligible upgrades.
- Database of State Incentives for Renewables & Efficiency — DSIRE — NC State University.State and utility incentive programs by ZIP code.
Homeowners in Irving often pair this with
A whole-house repipe rarely happens in isolation — these projects commonly come up alongside it.
Other projects in Irving
Browse local 2026 costs for every home project in Irving, TX.