Metal Roof Installation cost: Kent vs Tacoma (2026)
There's essentially no price gap here: metal roof installation runs close to $25,950 in both Kent and Tacoma in 2026.
Kent WA
Typically around $25,950
Tacoma WA
Typically around $25,950
Kent vs Tacoma: full breakdown
| Factor | Kent | Tacoma |
|---|---|---|
| Typical 2026 cost | $25,950 | $25,950 |
| Estimated range | $15,800–$36,050 | $15,800–$36,050 |
| Labor index (vs US) | ×1.19 | ×1.19 |
| Climate zone | Mixed | Mixed |
| Climate factor | ×1 | ×1 |
| Local permit | $325 | $325 |
| Labor share | $15,550 | $15,550 |
| Materials/equipment | $10,400 | $10,400 |
These are 2026 planning figures for metal roof installation, localized to each city — not formal quotes.
A wash — choose on quality, not city
With no real price gap on metal roof installation, the choice comes down to contractor quality and timing, not which city you're in.
Metal roof installation by type: Kent vs Tacoma
We localize each metal roof installation type separately for both metros, applying the same labor, climate and permit adjustments each time, so you're comparing like for like.
| Type | Kent | Tacoma |
|---|---|---|
| Corrugated steel (exposed fastener) | $11,050–$21,750 | $11,050–$21,750 |
| Standing-seam steel | $21,750–$42,000 | $21,750–$42,000 |
| Aluminum | $17,000–$33,700 | $17,000–$33,700 |
| Copper | $36,050–$71,800 | $36,050–$71,800 |
| Zinc | $33,700–$65,850 | $33,700–$65,850 |
These are 2026 planning figures for metal roof installation, localized to each city — not formal quotes.
Metal roof installation by roof size: Kent vs Tacoma
Metal roofing is priced per square (100 sq ft) and costs roughly $6–$14 per sq ft installed — two to three times asphalt, but it lasts decades longer. Standing-seam costs more than exposed-fastener panels.
| Size | Kent | Tacoma |
|---|---|---|
| 1,000 sq ft (10 squares) | $9,850–$19,400 | $9,850–$19,400 |
| 1,500 sq ft (15 squares) | $13,450–$27,750 | $13,450–$27,750 |
| 2,000 sq ft (20 squares) | $15,800–$36,050 | $15,800–$36,050 |
| 2,500 sq ft (25 squares) | $19,400–$43,200 | $19,400–$43,200 |
| 3,000+ sq ft (30 squares) | $22,950–$50,350 | $22,950–$50,350 |
Metal roof installation numbers here are 2026 planning ranges, adjusted per city — useful for budgeting, not a substitute for an actual quote.
What roofing pros earn in each metro
Labor is about 60% of a metal roof installation bill, so local wages drive most of the gap. These are real metro hourly wages for skilled installers (BLS OEWS), not estimates.
Seattle-Tacoma-Bellevue metro · about 32% above the US average installer wage.
Seattle-Tacoma-Bellevue metro · about 32% above the US average installer wage.
Source: U.S. Bureau of Labor Statistics, OEWS metro wages for HVAC installers (used as a trade-labor index).
Cheapest time for metal roof installation in either city
Shingles need warm, dry weather to seal, and demand peaks after summer storms. Booking in the slow late-fall/winter window for a spring install often earns you off-season pricing.
Where does a smart roofing budget go in 2026?
A roofing quote can hide a lot behind a single number — whether it's a true tear-off, the shingle grade, and what's under the surface. Here's how our editors sort through it.
The do-it-right case
Pay for a full tear-off and quality underlayment, flashing and ventilation. An overlay saves money today but traps heat, voids some warranties and costs more at the next replacement.
The risk case
Budget for the unknown: rotten decking found at tear-off is the most common surprise. Get the per-sheet repair rate in writing up front so a "cheap" bid doesn't balloon mid-job.
The value case
Architectural shingles sit between bargain 3-tab and premium metal or tile, and for most houses that middle ground is exactly right. They carry longer wind and wear ratings than 3-tab for a small step up in price, without the four-figure jump metal or tile demands.
The two things that actually protect a roofing budget are a real tear-off and a written rate for any deck repairs found along the way. The cheapest post-storm bid usually isn't the cheapest roof, long-term.
Kent vs Tacoma
Is metal roof installation cheaper in Kent or Tacoma?
Practically identical — expect around $25,950 for metal roof installation whichever city you're in.
Why does metal roof installation cost more in Tacoma than Kent?
Labor rates explain most of it — 1.19 in Tacoma vs 1.19 in Kent. A mixed climate versus mixed accounts for the rest.
How much is metal roof installation in Kent, WA?
metal roof installation in Kent runs $15,800–$36,050 as of 2026 — most jobs land near $25,950.
Do roofing pros really charge more in one city?
They do, and the BLS wage data confirms it: installers earn about $41.1/hr around Seattle-Tacoma-Bellevue versus $41.1/hr near Seattle-Tacoma-Bellevue. With labor making up about 60% of a metal roof installation job, that difference carries straight through to the final price.
When is the cheapest time to buy metal roof installation — and does it differ by city?
No, the seasonal pattern is the same in Kent and Tacoma: book during Late spring to early fall (dry, 45–85°F) for about 5–10% in savings. Mid-winter and the post-storm rush is the priciest stretch in both cities, mostly due to emergency replacements.
Should I choose where to live based on metal roof installation cost?
There's no cost argument here between Kent and Tacoma — they're a wash. Focus on contractor reputation, project scope, equipment tier and timing.
Compare metal roof installation in other cities
Updated June 2026 · By Serhat Özçelik