Furnace Replacement cost: Evanston vs Joliet (2026)
In 2026, Evanston and Joliet land on nearly identical furnace replacement pricing — about $6,850 either way.
Evanston IL
Typically around $6,850
Joliet IL
Typically around $6,850
Evanston vs Joliet: full breakdown
| Factor | Evanston | Joliet |
|---|---|---|
| Typical 2026 cost | $6,850 | $6,850 |
| Estimated range | $4,900–$8,800 | $4,900–$8,800 |
| Labor index (vs US) | ×1.14 | ×1.14 |
| Climate zone | Cold | Cold |
| Climate factor | ×1.08 | ×1.08 |
| Local permit | $225 | $225 |
| Labor share | $4,100 | $4,100 |
| Materials/equipment | $2,750 | $2,750 |
Furnace replacement numbers here are 2026 planning ranges, adjusted per city — useful for budgeting, not a substitute for an actual quote.
No real cost edge either way
This is a statistical tie on furnace replacement cost, so let contractor reputation and project timing decide, not geography.
Furnace replacement by type: Evanston vs Joliet
Below, each furnace replacement option is priced independently for both cities, with identical local labor, climate and permit logic applied — so the comparison holds up.
| Type | Evanston | Joliet |
|---|---|---|
| Gas furnace | $4,750–$8,700 | $4,750–$8,700 |
| High-efficiency gas furnace | $4,250–$8,700 | $4,250–$8,700 |
| Electric furnace | $2,700–$5,750 | $2,700–$5,750 |
These are 2026 planning figures for furnace replacement, localized to each city — not formal quotes.
Furnace replacement by home size: Evanston vs Joliet
Furnace cost scales with the heating capacity (BTU) your home needs — roughly 40–45 BTU per square foot in a mixed climate. Larger homes need a bigger unit and more ductwork.
| Size | Evanston | Joliet |
|---|---|---|
| 1,000 sq ft (≈45,000 BTU) | $3,650–$6,600 | $3,650–$6,600 |
| 1,500 sq ft (≈68,000 BTU) | $4,250–$7,600 | $4,250–$7,600 |
| 2,000 sq ft (≈90,000 BTU) | $4,900–$8,800 | $4,900–$8,800 |
| 2,500 sq ft (≈110,000 BTU) | $5,600–$10,050 | $5,600–$10,050 |
| 3,000 sq ft (≈130,000 BTU) | $6,350–$11,250 | $6,350–$11,250 |
| 3,500+ sq ft (≈150,000 BTU) | $7,100–$12,500 | $7,100–$12,500 |
All figures are 2026 localized planning estimates for furnace replacement — get an actual quote before you commit.
What hvac pros earn in each metro
With labor making up about 60% of a furnace replacement job, wage differences between metros do most of the work here. These figures are real BLS OEWS installer wages, not modeled estimates.
Chicago-Naperville-Elgin metro · about 23% above the US average installer wage.
Chicago-Naperville-Elgin metro · about 23% above the US average installer wage.
Source: U.S. Bureau of Labor Statistics, OEWS metro wages for HVAC installers (used as a trade-labor index).
Cheapest time for furnace replacement in either city
Crews are busiest — and priciest — exactly when it's hottest or coldest, since that's when systems fail under load. Book in the mild months and you're negotiating from a position of choice, not a broken furnace.
How much should you really budget for HVAC in 2026?
Ask five contractors for an HVAC quote and you'll get five different numbers — usually because they disagree on sizing, efficiency and equipment tier. Here's how our editors think through those trade-offs.
The efficiency-first case
Where you face brutal summers or hard winters, a higher SEER2/AFUE system or a heat pump runs enough hours to claw back its premium through lower bills — and utility or state rebates can still trim the sticker even though the federal 25C/25D credits closed at the end of 2025. Do the payback arithmetic before you reach for the cheapest box on the lot.
The budget-first case
Size the system to your home with a Manual J calculation and buy the standard efficiency tier (80% AFUE / 14.3 SEER2). In a mild climate the cheaper unit pays off because you rarely run it hard — paying for premium efficiency you won't use is the most common way to overspend.
The longevity case
Brand is a footnote; sizing and install quality write the story. A right-sized mid-tier system that's properly commissioned and serviced once a year will outlive an oversized premium unit that short-cycles itself to an early grave. Put the money into the crew and the setup rather than the nameplate.
The costly errors in an HVAC job are a bad load calculation and a sloppy install — not the logo you chose. Size it with a real Manual J, let your climate set the efficiency tier, and claim whatever rebates you still qualify for.
Evanston vs Joliet
Is furnace replacement cheaper in Evanston or Joliet?
Practically identical — expect around $6,850 for furnace replacement whichever city you're in.
Why does furnace replacement cost more in Joliet than Evanston?
Labor rates explain most of it — 1.14 in Joliet vs 1.14 in Evanston. A cold climate versus cold accounts for the rest.
How much is furnace replacement in Evanston, IL?
Evanston homeowners can expect $4,900 to $8,800 for furnace replacement in 2026, with $6,850 the typical number.
Do hvac pros really charge more in one city?
It's not a myth — BLS data puts installer wages at about $38.1/hr in the Chicago-Naperville-Elgin area and $38.1/hr in Chicago-Naperville-Elgin. Given labor is around 60% of a furnace replacement job's cost, that gap explains most of the price spread.
When is the cheapest time to buy furnace replacement — and does it differ by city?
The best window is the same in both Evanston and Joliet: Spring and fall (Mar–May, Sep–Oct), when demand drops and installers discount to keep crews busy — typically 5–15% off peak pricing. The most expensive time anywhere is an emergency replacement during peak summer and mid-winter.
Should I choose where to live based on furnace replacement cost?
There's no cost argument here between Evanston and Joliet — they're a wash. Focus on contractor reputation, project scope, equipment tier and timing.
Compare furnace replacement in other cities
Updated June 2026 · By Serhat Özçelik