Furnace Replacement cost: Columbus vs Evansville (2026)
In 2026, furnace replacement is about 11% more expensive in Columbus than in Evansville. Most homeowners pay around $6,250 in Columbus versus $5,650 in Evansville — a gap of roughly $600.
Columbus IN
Typically around $6,250
Evansville IN
Lower costTypically around $5,650
Columbus vs Evansville: full breakdown
| Factor | Columbus | Evansville |
|---|---|---|
| Typical 2026 cost | $6,250 | $5,650 |
| Estimated range | $4,450–$8,050 | $4,050–$7,250 |
| Labor index (vs US) | ×1.04 | ×0.93 |
| Climate zone | Cold | Cold |
| Climate factor | ×1.08 | ×1.08 |
| Local permit | $200 | $200 |
| Labor share | $3,750 | $3,400 |
| Materials/equipment | $2,500 | $2,250 |
These are 2026 planning figures for furnace replacement, localized to each city — not formal quotes.
Is the price difference a dealbreaker?
11% (about $600) is enough to notice on a furnace replacement budget. Timing the purchase for the off-season and pushing for an apples-to-apples bid in Columbus can close much of that gap.
Furnace replacement by type: Columbus vs Evansville
Below, each furnace replacement option is priced independently for both cities, with identical local labor, climate and permit logic applied — so the comparison holds up.
| Type | Columbus | Evansville |
|---|---|---|
| Gas furnace | $4,350–$7,900 | $3,950–$7,150 |
| High-efficiency gas furnace | $3,900–$7,900 | $3,550–$7,150 |
| Electric furnace | $2,450–$5,250 | $2,200–$4,750 |
These are 2026 planning figures for furnace replacement, localized to each city — not formal quotes.
Furnace replacement by home size: Columbus vs Evansville
Furnace cost scales with the heating capacity (BTU) your home needs — roughly 40–45 BTU per square foot in a mixed climate. Larger homes need a bigger unit and more ductwork.
| Size | Columbus | Evansville |
|---|---|---|
| 1,000 sq ft (≈45,000 BTU) | $3,350–$6,000 | $3,000–$5,450 |
| 1,500 sq ft (≈68,000 BTU) | $3,900–$6,900 | $3,550–$6,250 |
| 2,000 sq ft (≈90,000 BTU) | $4,450–$8,050 | $4,050–$7,250 |
| 2,500 sq ft (≈110,000 BTU) | $5,150–$9,150 | $4,650–$8,250 |
| 3,000 sq ft (≈130,000 BTU) | $5,800–$10,300 | $5,250–$9,300 |
| 3,500+ sq ft (≈150,000 BTU) | $6,450–$11,400 | $5,850–$10,300 |
Localized 2026 planning estimates — not quotes. Each city adjusts the national furnace replacement range for local labor, climate and permits.
What hvac pros earn in each metro
With labor making up about 60% of a furnace replacement job, wage differences between metros do most of the work here. These figures are real BLS OEWS installer wages, not modeled estimates.
Columbus metro · about 6% above the US average installer wage.
No BLS metro wage series for Evansville; we use Indiana regional price parity instead.
Source: U.S. Bureau of Labor Statistics, OEWS metro wages for HVAC installers (used as a trade-labor index).
Cheapest time for furnace replacement in either city
Why spring and fall are cheaper: contractors have open calendar space and compete harder for the work. Why summer and deep winter are expensive: a broken system in extreme weather isn't optional, so you lose your negotiating leverage.
How much should you really budget for HVAC in 2026?
Three factors move an HVAC quote more than anything else: how well it's sized, which efficiency tier you pick, and the brand markup. Our editors break down how they weigh each one.
The budget-first case
In a temperate region the smart move is to size the job correctly with a Manual J and take the base efficiency tier. A system that spends most days coasting can't recover the cost of a high-SEER2 compressor, because the savings only show up under heavy load you don't put on it. Match the equipment to how little you actually run it, not to the brochure's top number.
The longevity case
Brand is a footnote; sizing and install quality write the story. A right-sized mid-tier system that's properly commissioned and serviced once a year will outlive an oversized premium unit that short-cycles itself to an early grave. Put the money into the crew and the setup rather than the nameplate.
The efficiency-first case
Where you face brutal summers or hard winters, a higher SEER2/AFUE system or a heat pump runs enough hours to claw back its premium through lower bills — and utility or state rebates can still trim the sticker even though the federal 25C/25D credits closed at the end of 2025. Do the payback arithmetic before you reach for the cheapest box on the lot.
Match the efficiency tier to your climate, insist on a real load calculation, and stack every rebate you qualify for. The expensive mistakes are wrong sizing and a rushed install — not picking the "wrong" brand.
Columbus vs Evansville
Is furnace replacement cheaper in Columbus or Evansville?
Evansville comes out ahead here, at roughly $5,650 for furnace replacement compared with $6,250 in Columbus — a 11% ($600) gap as of 2026.
Why does furnace replacement cost more in Columbus than Evansville?
Labor rates explain most of it — 1.04 in Columbus vs 0.93 in Evansville. A cold climate versus cold accounts for the rest.
How much is furnace replacement in Columbus, IN?
furnace replacement in Columbus runs $4,450–$8,050 as of 2026 — most jobs land near $6,250.
When is the cheapest time to buy furnace replacement — and does it differ by city?
It doesn't vary by location — Spring and fall (Mar–May, Sep–Oct) is the discount window in both Columbus and Evansville (roughly 5–15% off), while peak summer and mid-winter tends to be the most expensive in either city.
Should I choose where to live based on furnace replacement cost?
Not really — the $600 gap is one-time, and smart timing and tighter quotes in Columbus can shrink it. Factors that compound over time, like energy prices and home condition, deserve more weight than a single upfront difference.
Compare furnace replacement in other cities
Updated June 2026 · By Serhat Özçelik