Furnace Replacement cost: Casper vs Evansville (2026)
Casper runs 2% higher than Evansville for furnace replacement — expect around $5,750 in Casper against $5,650 in Evansville, a difference of about $100.
Casper WY
Typically around $5,750
Evansville IN
Lower costTypically around $5,650
Casper vs Evansville: full breakdown
| Factor | Casper | Evansville |
|---|---|---|
| Typical 2026 cost | $5,750 | $5,650 |
| Estimated range | $4,100–$7,400 | $4,050–$7,250 |
| Labor index (vs US) | ×0.95 | ×0.93 |
| Climate zone | Cold | Cold |
| Climate factor | ×1.08 | ×1.08 |
| Local permit | $200 | $200 |
| Labor share | $3,450 | $3,400 |
| Materials/equipment | $2,300 | $2,250 |
All figures are 2026 localized planning estimates for furnace replacement — get an actual quote before you commit.
Is the price difference a dealbreaker?
2% is within noise for furnace replacement — contractor selection and timing move the price more than which of these two metros you're in.
Furnace replacement by type: Casper vs Evansville
Below, each furnace replacement option is priced independently for both cities, with identical local labor, climate and permit logic applied — so the comparison holds up.
| Type | Casper | Evansville |
|---|---|---|
| Gas furnace | $4,000–$7,300 | $3,950–$7,150 |
| High-efficiency gas furnace | $3,600–$7,300 | $3,550–$7,150 |
| Electric furnace | $2,250–$4,850 | $2,200–$4,750 |
These are 2026 planning figures for furnace replacement, localized to each city — not formal quotes.
Furnace replacement by home size: Casper vs Evansville
Furnace cost scales with the heating capacity (BTU) your home needs — roughly 40–45 BTU per square foot in a mixed climate. Larger homes need a bigger unit and more ductwork.
| Size | Casper | Evansville |
|---|---|---|
| 1,000 sq ft (≈45,000 BTU) | $3,100–$5,550 | $3,000–$5,450 |
| 1,500 sq ft (≈68,000 BTU) | $3,600–$6,350 | $3,550–$6,250 |
| 2,000 sq ft (≈90,000 BTU) | $4,100–$7,400 | $4,050–$7,250 |
| 2,500 sq ft (≈110,000 BTU) | $4,700–$8,450 | $4,650–$8,250 |
| 3,000 sq ft (≈130,000 BTU) | $5,350–$9,450 | $5,250–$9,300 |
| 3,500+ sq ft (≈150,000 BTU) | $5,950–$10,500 | $5,850–$10,300 |
Furnace replacement numbers here are 2026 planning ranges, adjusted per city — useful for budgeting, not a substitute for an actual quote.
Cheapest time for furnace replacement in either city
A furnace or AC that dies mid-heat-wave gets replaced at whatever the on-call crew charges. One that gets swapped in April or October gets a competitive, unhurried quote instead.
How much should you really budget for HVAC in 2026?
An HVAC budget isn't one number — it's a set of trade-offs between sizing accuracy, efficiency tier and brand. Our editors walk through how each one moves the price.
The longevity case
The most expensive variable on the quote isn't the logo — it's whether the system is sized right and installed well. Oversize a premium unit and it short-cycles, wears fast and underperforms; commission a correctly sized mid-tier one and keep up the annual service, and it simply lasts longer. Spend on the installation, not the badge.
The budget-first case
Run a Manual J load calculation, then buy the standard tier — 80% AFUE, 14.3 SEER2 — and stop there. Where summers are short and winters are gentle, the equipment idles most of the year, so premium efficiency never gets enough runtime to earn back its price. Paying for SEER2 you'll rarely tap is the classic way a mild-climate homeowner overspends.
The efficiency-first case
Where you face brutal summers or hard winters, a higher SEER2/AFUE system or a heat pump runs enough hours to claw back its premium through lower bills — and utility or state rebates can still trim the sticker even though the federal 25C/25D credits closed at the end of 2025. Do the payback arithmetic before you reach for the cheapest box on the lot.
Get the sizing and the commissioning right and the brand debate mostly disappears. Insist on a Manual J, pick an efficiency tier your climate can justify, and pocket every incentive that still applies after the federal credits lapsed.
Casper vs Evansville
Is furnace replacement cheaper in Casper or Evansville?
Evansville comes out ahead here, at roughly $5,650 for furnace replacement compared with $5,750 in Casper — a 2% ($100) gap as of 2026.
Why does furnace replacement cost more in Casper than Evansville?
Labor rates explain most of it — 0.95 in Casper vs 0.93 in Evansville. A cold climate versus cold accounts for the rest.
How much is furnace replacement in Casper, WY?
Casper homeowners can expect $4,100 to $7,400 for furnace replacement in 2026, with $5,750 the typical number.
When is the cheapest time to buy furnace replacement — and does it differ by city?
No, the seasonal pattern is the same in Casper and Evansville: book during Spring and fall (Mar–May, Sep–Oct) for about 5–15% in savings. Peak summer and mid-winter is the priciest stretch in both cities, mostly due to emergency replacements.
Should I choose where to live based on furnace replacement cost?
That would be a stretch. $100 is a one-time difference, not an ongoing one, and off-season buying plus apples-to-apples bids in Casper can close a good chunk of it. What matters more long-term is energy costs, climate and the condition of the home.
Compare furnace replacement in other cities
Updated June 2026 · By Serhat Özçelik