Furnace Replacement cost: Bloomington vs Edina (2026)
In 2026, Bloomington and Edina land on nearly identical furnace replacement pricing — about $6,700 either way.
Bloomington MN
Typically around $6,700
Edina MN
Typically around $6,700
Bloomington vs Edina: full breakdown
| Factor | Bloomington | Edina |
|---|---|---|
| Typical 2026 cost | $6,700 | $6,700 |
| Estimated range | $4,750–$8,600 | $4,750–$8,600 |
| Labor index (vs US) | ×1.11 | ×1.11 |
| Climate zone | Cold | Cold |
| Climate factor | ×1.08 | ×1.08 |
| Local permit | $225 | $225 |
| Labor share | $4,000 | $4,000 |
| Materials/equipment | $2,700 | $2,700 |
Localized 2026 planning estimates — not quotes. Each city adjusts the national furnace replacement range for local labor, climate and permits.
Basically a tie — focus on the contractor
Neither metro has a cost edge on furnace replacement — spend your decision-making energy on the contractor, not the location.
Furnace replacement by type: Bloomington vs Edina
Every furnace replacement type gets its own localized price for each metro, using the same labor, climate and permit adjustments — a true apples-to-apples comparison.
| Type | Bloomington | Edina |
|---|---|---|
| Gas furnace | $4,650–$8,450 | $4,650–$8,450 |
| High-efficiency gas furnace | $4,150–$8,450 | $4,150–$8,450 |
| Electric furnace | $2,600–$5,600 | $2,600–$5,600 |
Furnace replacement numbers here are 2026 planning ranges, adjusted per city — useful for budgeting, not a substitute for an actual quote.
Furnace replacement by home size: Bloomington vs Edina
Furnace cost scales with the heating capacity (BTU) your home needs — roughly 40–45 BTU per square foot in a mixed climate. Larger homes need a bigger unit and more ductwork.
| Size | Bloomington | Edina |
|---|---|---|
| 1,000 sq ft (≈45,000 BTU) | $3,550–$6,450 | $3,550–$6,450 |
| 1,500 sq ft (≈68,000 BTU) | $4,150–$7,400 | $4,150–$7,400 |
| 2,000 sq ft (≈90,000 BTU) | $4,750–$8,600 | $4,750–$8,600 |
| 2,500 sq ft (≈110,000 BTU) | $5,500–$9,800 | $5,500–$9,800 |
| 3,000 sq ft (≈130,000 BTU) | $6,200–$11,000 | $6,200–$11,000 |
| 3,500+ sq ft (≈150,000 BTU) | $6,900–$12,200 | $6,900–$12,200 |
Furnace replacement numbers here are 2026 planning ranges, adjusted per city — useful for budgeting, not a substitute for an actual quote.
What hvac pros earn in each metro
Since labor accounts for around 60% of what a furnace replacement job costs, it's the biggest lever behind any price gap between cities. What you're seeing below is actual BLS metro wage data for skilled installers — not a guess.
Minneapolis-St. Paul-Bloomington metro · about 18% above the US average installer wage.
Minneapolis-St. Paul-Bloomington metro · about 18% above the US average installer wage.
Source: U.S. Bureau of Labor Statistics, OEWS metro wages for HVAC installers (used as a trade-labor index).
Cheapest time for furnace replacement in either city
Installers cut prices in spring and fall because job volume drops and crews sit idle — the opposite happens during a summer heat wave or winter cold snap, when a dead system forces homeowners into a full-price emergency swap.
How much should you really budget for HVAC in 2026?
Three factors move an HVAC quote more than anything else: how well it's sized, which efficiency tier you pick, and the brand markup. Our editors break down how they weigh each one.
The longevity case
The single biggest cost driver isn't the brand — it's correct sizing and install quality. A properly sized, well-commissioned mid-tier system with annual maintenance outlasts an oversized premium unit that short-cycles. Spend on the install, not the badge.
The budget-first case
Run a Manual J load calculation, then buy the standard tier — 80% AFUE, 14.3 SEER2 — and stop there. Where summers are short and winters are gentle, the equipment idles most of the year, so premium efficiency never gets enough runtime to earn back its price. Paying for SEER2 you'll rarely tap is the classic way a mild-climate homeowner overspends.
The efficiency-first case
Where you face brutal summers or hard winters, a higher SEER2/AFUE system or a heat pump runs enough hours to claw back its premium through lower bills — and utility or state rebates can still trim the sticker even though the federal 25C/25D credits closed at the end of 2025. Do the payback arithmetic before you reach for the cheapest box on the lot.
Skip the brand debate. A correctly sized system, an efficiency tier that fits your climate, and a properly commissioned install will save you more than any label ever could.
Bloomington vs Edina
Is furnace replacement cheaper in Bloomington or Edina?
Not really — both cities land at almost the same number for furnace replacement, around $6,700 each.
Why does furnace replacement cost more in Edina than Bloomington?
Edina's higher labor index (1.11 vs 1.11 in Bloomington) is the biggest factor, with the cold/cold climate split playing a smaller role.
How much is furnace replacement in Bloomington, MN?
Bloomington homeowners can expect $4,750 to $8,600 for furnace replacement in 2026, with $6,700 the typical number.
Do hvac pros really charge more in one city?
It's not a myth — BLS data puts installer wages at about $36.7/hr in the Minneapolis-St. Paul-Bloomington area and $36.7/hr in Minneapolis-St. Paul-Bloomington. Given labor is around 60% of a furnace replacement job's cost, that gap explains most of the price spread.
When is the cheapest time to buy furnace replacement — and does it differ by city?
Timing doesn't change by city here — Spring and fall (Mar–May, Sep–Oct) is the cheapest window in both Bloomington and Edina, saving roughly 5–15%. Avoid peak summer and mid-winter in either location, when emergency replacements push prices up.
Should I choose where to live based on furnace replacement cost?
No — the cost is essentially identical between Bloomington and Edina. Base the decision on the things that actually vary: contractor reputation, scope, equipment tier and timing.
Compare furnace replacement in other cities
Updated June 2026 · By Serhat Özçelik