Furnace Replacement cost: Anderson vs Evansville (2026)
The two metros aren't quite in sync on furnace replacement: Anderson sits 1% below Evansville, or roughly $5,600 versus $5,650 — about $50 apart.
Anderson IN
Lower costTypically around $5,600
Evansville IN
Typically around $5,650
Anderson vs Evansville: full breakdown
| Factor | Anderson | Evansville |
|---|---|---|
| Typical 2026 cost | $5,600 | $5,650 |
| Estimated range | $4,000–$7,200 | $4,050–$7,250 |
| Labor index (vs US) | ×0.93 | ×0.93 |
| Climate zone | Cold | Cold |
| Climate factor | ×1.08 | ×1.08 |
| Local permit | $200 | $200 |
| Labor share | $3,350 | $3,400 |
| Materials/equipment | $2,250 | $2,250 |
Furnace replacement numbers here are 2026 planning ranges, adjusted per city — useful for budgeting, not a substitute for an actual quote.
Is the price difference a dealbreaker?
A 1% difference on furnace replacement is minor — you'll typically see a wider spread just from getting multiple quotes in the same city, so don't let location drive the decision.
Furnace replacement by type: Anderson vs Evansville
Each furnace replacement option, priced separately for both metros — the same local labor, climate and permit adjustments applied per city, so you can compare like for like.
| Type | Anderson | Evansville |
|---|---|---|
| Gas furnace | $3,900–$7,100 | $3,950–$7,150 |
| High-efficiency gas furnace | $3,500–$7,100 | $3,550–$7,150 |
| Electric furnace | $2,200–$4,700 | $2,200–$4,750 |
Localized 2026 planning estimates — not quotes. Each city adjusts the national furnace replacement range for local labor, climate and permits.
Furnace replacement by home size: Anderson vs Evansville
Furnace cost scales with the heating capacity (BTU) your home needs — roughly 40–45 BTU per square foot in a mixed climate. Larger homes need a bigger unit and more ductwork.
| Size | Anderson | Evansville |
|---|---|---|
| 1,000 sq ft (≈45,000 BTU) | $3,000–$5,400 | $3,000–$5,450 |
| 1,500 sq ft (≈68,000 BTU) | $3,500–$6,200 | $3,550–$6,250 |
| 2,000 sq ft (≈90,000 BTU) | $4,000–$7,200 | $4,050–$7,250 |
| 2,500 sq ft (≈110,000 BTU) | $4,600–$8,200 | $4,650–$8,250 |
| 3,000 sq ft (≈130,000 BTU) | $5,200–$9,200 | $5,250–$9,300 |
| 3,500+ sq ft (≈150,000 BTU) | $5,800–$10,200 | $5,850–$10,300 |
All figures are 2026 localized planning estimates for furnace replacement — get an actual quote before you commit.
Cheapest time for furnace replacement in either city
HVAC demand collapses in the mild shoulder seasons, so installers discount to keep crews busy. The most expensive time to buy is during a heat wave or cold snap, when a dead system forces a full-price emergency replacement.
How much should you really budget for HVAC in 2026?
Three factors move an HVAC quote more than anything else: how well it's sized, which efficiency tier you pick, and the brand markup. Our editors break down how they weigh each one.
The longevity case
The single biggest cost driver isn't the brand — it's correct sizing and install quality. A properly sized, well-commissioned mid-tier system with annual maintenance outlasts an oversized premium unit that short-cycles. Spend on the install, not the badge.
The efficiency-first case
Where you face brutal summers or hard winters, a higher SEER2/AFUE system or a heat pump runs enough hours to claw back its premium through lower bills — and utility or state rebates can still trim the sticker even though the federal 25C/25D credits closed at the end of 2025. Do the payback arithmetic before you reach for the cheapest box on the lot.
The budget-first case
In a temperate region the smart move is to size the job correctly with a Manual J and take the base efficiency tier. A system that spends most days coasting can't recover the cost of a high-SEER2 compressor, because the savings only show up under heavy load you don't put on it. Match the equipment to how little you actually run it, not to the brochure's top number.
Match the efficiency tier to your climate, insist on a real load calculation, and stack every rebate you qualify for. The expensive mistakes are wrong sizing and a rushed install — not picking the "wrong" brand.
Anderson vs Evansville
Is furnace replacement cheaper in Anderson or Evansville?
Yes — Evansville costs more. Expect around $5,650 for furnace replacement there against $5,600 in Anderson, about $50 (1%) apart in 2026.
Why does furnace replacement cost more in Evansville than Anderson?
It comes down to labor: Evansville indexes at 0.93 against Anderson's 0.93. The cold-vs-cold climate difference adds to the gap.
How much is furnace replacement in Anderson, IN?
Expect to pay $4,000 to $7,200 for furnace replacement in Anderson in 2026, averaging around $5,600.
When is the cheapest time to buy furnace replacement — and does it differ by city?
Timing doesn't change by city here — Spring and fall (Mar–May, Sep–Oct) is the cheapest window in both Anderson and Evansville, saving roughly 5–15%. Avoid peak summer and mid-winter in either location, when emergency replacements push prices up.
Should I choose where to live based on furnace replacement cost?
That would be a stretch. $50 is a one-time difference, not an ongoing one, and off-season buying plus apples-to-apples bids in Evansville can close a good chunk of it. What matters more long-term is energy costs, climate and the condition of the home.
Compare furnace replacement in other cities
Updated June 2026 · By Serhat Özçelik