Plumbing · Tigard, OR
How much does whole-house repipe cost in Tigard, OR? (2026)
In Tigard, whole-house repipe runs $3,900–$8,850, with most paying around $6,400 — about 12% above the national average. Replacing a home's water supply piping — typically swapping old galvanized or failing pipe for PEX or copper.
Updated June 2026 · Localized estimate, not a quote
Most homeowners pay around $6,400
- Typical cost
- $6,400
- Labor vs US
- +9%
- Climate
- Mixed
- Local permit
- $275
Refine your estimate
Tune it to your home to narrow the whole-house repipe range.
Key takeaways for Tigard
- $3,900 on the low end, $8,850 on the high — whole-house repipe in Tigard averages $6,400, about 12% above the national average.
- Labor is the swing factor here: Tigard trades bill +9% relative to the national average.
- Permit costs are baked in: Tigard charges about $275 for the Plumbing permit.
- Count on 50–100 years from a solid install; timing the next job yourself avoids the emergency premium.
- Cheapest time to buy: Off-peak winter for planned work — roughly Around 5% off peak-season pricing.
What goes into the price in Tigard
A typical Tigard whole-house repipe of $6,400 breaks down roughly like this — materials priced near the national level, labor set by local rates.
| Line item | Tigard 2026 range |
|---|---|
| Materials & equipmentUnit, materials and supplies — priced close to the national level. | $1,450 – $3,450 |
| Labor & installationRemoval, install and startup labor — the line most affected by where you live. | $2,175 – $5,125 |
| Permit & feesLocal building-department fee for Plumbing work here. | $275 |
| Total installed cost | $3,900 – $8,850 |
Split from the Tigard estimate using a 60% local-labor share; line items sum to the total.
Why whole-house repipe costs what it does in Tigard
- Tigard's labor rates sit about 9% higher than the national average (based on price levels for the Portland-Vancouver-Hillsboro metro area), pushing the price up.
- A Plumbing permit in Tigard costs around $275, included above.
Whole House Repipe cost by home size in Tigard
Repipe cost scales with how many bathrooms and fixtures the crew has to reach — more baths means more runs, more wall and ceiling access, and more labor. Pricing below assumes standard single-story access.
| home size | Tigard 2026 range |
|---|---|
| 1 bath / ~1,000 sq ft | $3,500 – $6,200 |
| 2 bath / ~1,500 sq ft | $4,350 – $7,800 |
| 3 bath / ~2,000 sq ft | $5,450 – $9,950 |
| 4+ bath / 2,500+ sq ft | $6,700 – $13,150 |
National size ranges localized to Tigard labor and climate.
Whole House Repipe cost by type in Tigard
| PEX | $3,900 – $7,750 |
| CPVC | $4,550 – $8,850 |
| Copper | $6,700 – $16,350 |
Adjusted to Tigard from national type-level ranges.
Whole House Repipe cost by efficiency in Tigard
The pipe material drives both price and longevity. PEX is flexible, fast to run, and the cheapest to install; rigid copper costs more in material and labor but is the long-haul standard many buyers prefer.
| PEX (cross-linked polyethylene)Cheapest to install; flexible, freeze-tolerant | $3,500 – $6,700 |
| CPVCMid-cost rigid plastic; common in hot-water lines | $4,050 – $7,800 |
| Copper (rigid)Highest cost; long lifespan, resale appeal | $5,650 – $13,150 |
Labor vs. materials in Tigard
Install crew, removal, permit & startup — the part Tigard rates move most.
Equipment & materials — priced closer to the national level.
Split based on a typical $6,400 Tigard project; your mix varies with scope.
Skilled installers in the Portland-Vancouver-Hillsboro area earn about $34.9/hr (12% above the US average, per BLS metro wage data) — the local wage is what moves the labor half of your whole-house repipe cost.
How we estimate it
| National range | $3,400 – $8,000 |
| Tigard labor adjustment | ×1.07 |
| mixed climate factor | ×1 |
| Local permit | +$275 |
| Tigard estimate | $3,900 – $8,850 |
Promo prices vs. the real cost
The fee to get a plumber to your door tells you nothing about what the repair itself runs:
- Camera inspection$100–$350 (sometimes waived)
- "Free" estimate on big jobs$0 — it's a sales visit
- Service / diagnostic call$75–$200
Additional whole-house repipe costs to budget for
Some of these land on the final invoice and some never surface — it comes down to your home's age, access and existing setup.
| Drywall & wall/ceiling patch + repaintCrews open walls to reach pipes; finishing is often separate | $500 – $3,000 |
| Permit & inspection | $100 – $500 |
| Move out / hotel during workWhole-house repipes can take 2–5 days with water off | $0 – $1,000 |
| Replace shutoff valves & supply lines | $150 – $600 |
| Slab access / concrete cut (slab homes)Only if lines run under a concrete slab | $1,000 – $4,000 |
Typical national add-on ranges; confirm locally during your quote.
What's included
- Removal of accessible old piping
- New PEX or copper supply lines
- Basic drywall patching and permit
- Fixture reconnections
What affects the cost
- Wall opening and patching needed
- Home size and number of bathrooms
- PEX vs copper
- Slab vs crawlspace/basement access
Ways to save on whole-house repipe in Tigard
- Act before a leak causes water damage
- Repipe during a remodel to share wall access
- PEX costs less than copper and installs faster
- Get multiple licensed-plumber bids
How long does whole-house repipe last in Tigard?
PEX and CPVC last ~40–50+ years; copper commonly reaches 50–70+ years. A repipe is essentially a once-in-a-lifetime job.
Repiped supply lines need almost no upkeep; budget only for the occasional shutoff-valve or fixture check.
Signs you need whole-house repipe in Tigard
- Chronic low water pressure throughout the house
- Rusty, brown, or metallic-tasting water (corroding pipes)
- Frequent or repeated pinhole leaks and pipe repairs
- Old galvanized steel, polybutylene, or lead supply pipes
- Banging, knocking, or whistling pipes (water hammer / corrosion)
- Visible corrosion, flaking, or green stains on exposed pipe
- The home is 50+ years old on its original plumbing
Repair or replace in Tigard?
Repair if…
- A single, accessible leak in otherwise sound modern pipe (PEX/copper)
- The rest of the system is under ~25 years old and leak-free
- The damaged section is short and easy to isolate
Replace if…
- Pipes are galvanized steel, polybutylene, or lead
- Leaks keep recurring in different spots (systemic corrosion)
- Water pressure and water quality are both declining
- You're already gutting walls for a remodel (do it once)
Cheapest time for whole-house repipe in Tigard
Emergency plumbing work is priced for urgency, full stop. A repipe or sewer line, on the other hand, is a project you can schedule — and scheduling it for a slow month gets you a slightly better rate and a crew that isn't rushing.
Why whole-house repipe quotes vary — and how to compare them fairly
One bid high, one low, same house? The variable is scope. Here's what pushes the figure up or down and how to get quotes you can actually compare.
Why a quote looks high (or low)
- Permits, inspection and surface/landscape restoration may be excluded.
- Scope is often unknown until a camera inspection confirms it.
- Pipe material (PEX vs. copper) changes both cost and longevity.
Get an apples-to-apples bid
- Ask whether trenchless or dig fits your situation and why.
- Require a camera inspection so the scope is confirmed before work.
- Confirm permits, inspection and restoration are included.
- Clarify who owns the city-side portion of the line.
Questions to ask Tigard Plumbing pros
You can't judge bids side by side unless they cover the same ground; run through these with every pro on your list.
- 1Trenchless vs. traditional dig — which fits my situation and why?
- 2Is a camera inspection included so we confirm the scope before digging?
- 3Are permits, inspection, and surface/landscape restoration included?
- 4What pipe material are you using (PEX vs. copper) and why?
- 5Who is responsible for the city-owned portion of the line?
Whole House Repipe in Tigard
How much does whole-house repipe cost in Tigard, OR?
Most Tigard homeowners pay around $6,400 for whole-house repipe, though 2026 quotes stretch from $3,900 to $8,850. Local labor, the mixed climate and permit fees are all baked into that number.
Is whole-house repipe more expensive in Tigard than average?
Labor is the biggest lever here: at an index of 1.07 versus the US average, Tigard ends up about 12% higher than the national average.; add in a Plumbing permit at roughly $275.
Do I need a permit for whole-house repipe in Tigard?
In Tigard, this usually needs a Plumbing permit (around $275). The estimate above already accounts for it.
What affects whole-house repipe cost the most?
Replacing a home's water supply piping — typically swapping old galvanized or failing pipe for PEX or copper. From there, a handful of specifics push the final number up or down. What should you watch? Equipment or material grade, the home's size and complexity, local labor rates, and your mixed climate zone — in roughly that order.
How do you budget a major plumbing job?
Big plumbing jobs are unpredictable by nature — the method chosen and what's actually underground move the price more than anything else. Our editors weigh in.
The material case
PEX is cheaper, faster and freeze-tolerant; copper costs more but lasts longer and some buyers prefer it. Match the material to your climate and how long you'll own the home.
The diagnosis-first case
Pricing a sewer or repipe off a hunch invites two bad outcomes: paying to replace pipe that's fine, or missing the section that's actually collapsed. A camera run through the line settles the question before a single dollar is committed.
The method case
Trenchless runs a higher per-foot rate, but the savings hide in what you never have to rebuild — no torn-up driveway, no re-sodded lawn, no ripped-out patio. Open-cut digging only wins on price when there's almost nothing on top of the line to put back.
Scope, not brand, is what sets a plumbing price. Confirm it with a camera inspection, compare trenchless against the full cost of a dig — landscaping included — and match pipe material to your climate.
Editorial analysis by Serhat Özçelik, reviewed by Costadia Editorial. These are our own cost perspectives, not third-party endorsements.
How we calculated this estimate
We start with 2026 national whole-house repipe ranges compiled from contractor-pricing sources (Angi, HomeGuide, Fixr and EnergySage averages), then localize them to Tigard using the BLS metro wage data labor index (×1.07 here), the IECC mixed-climate factor (×1) and a typical local permit fee (≈$275). Federal incentive details reference the IRS Inflation Reduction Act (25C/25D) and DSIRE.
This is a planning estimate, not a quote.Actual prices vary with your home's condition, equipment grade and contractor — always confirm with licensed local pros before budgeting.
References & data sources
Our Tigard whole-house repipe estimate is built from these primary, mostly government sources — not a single aggregator.
- Occupational Employment & Wage Statistics (metro wages) — U.S. Bureau of Labor Statistics.Metro-level trade wages behind each city's labor index.
- Regional Price Parities (state & metro) — U.S. Bureau of Economic Analysis.Regional price levels used where metro wage data is unavailable.
- IECC Climate Zones — U.S. DOE — Building Energy Codes Program.Climate-zone factors applied to weather-sensitive projects.
- Home Energy Tax Credits (25C / 25D) — Internal Revenue Service.Federal rebate and tax-credit figures for eligible upgrades.
- Database of State Incentives for Renewables & Efficiency — DSIRE — NC State University.State and utility incentive programs by ZIP code.
Homeowners in Tigard often pair this with
A whole-house repipe rarely happens in isolation — these projects commonly come up alongside it.
Other projects in Tigard
Browse local 2026 costs for every home project in Tigard, OR.