Plumbing · St. Louis, MO
How much does whole-house repipe cost in St. Louis, MO? (2026)
In St. Louis, whole-house repipe runs $3,600–$8,100, with most paying around $5,850 — about 3% above the national average. Replacing a home's water supply piping — typically swapping old galvanized or failing pipe for PEX or copper.
Updated June 2026 · Localized estimate, not a quote
Most homeowners pay around $5,850
- Typical cost
- $5,850
- Labor vs US
- −3%
- Climate
- Mixed
- Local permit
- $250
Refine your estimate
Tune it to your home to narrow the whole-house repipe range.
Key takeaways for St. Louis
- Priced about 3% above the national average, whole-house repipe in St. Louis spans $3,600 to $8,100 — figure $5,850 for a standard job.
- Labor is the swing factor here: St. Louis trades bill −3% relative to the national average.
- Permit costs are baked in: St. Louis charges about $250 for the Plumbing permit.
- Count on 50–100 years from a solid install; timing the next job yourself avoids the emergency premium.
- Time it right and you can save Around 5%: the best window to book is Off-peak winter for planned work.
What goes into the price in St. Louis
A typical St. Louis whole-house repipe of $5,850 breaks down roughly like this — materials priced near the national level, labor set by local rates.
| Line item | St. Louis 2026 range |
|---|---|
| Materials & equipmentThe equipment and materials themselves — this part barely shifts by location. | $1,350 – $3,150 |
| Labor & installationCrew time for removal, installation and startup; local labor rates drive most of the swing here. | $2,000 – $4,700 |
| Permit & feesPlumbing permit cost, adjusted to this city's rate. | $250 |
| Total installed cost | $3,600 – $8,100 |
Split from the St. Louis estimate using a 60% local-labor share; line items sum to the total.
Why whole-house repipe costs what it does in St. Louis
- Expect labor here to run 3% below the national norm (based on price levels for the St. Louis metro area) — that's what lowers the total.
- St. Louis's Plumbing permit runs roughly $250, which is already part of the number above.
Whole House Repipe cost by home size in St. Louis
Repipe cost scales with how many bathrooms and fixtures the crew has to reach — more baths means more runs, more wall and ceiling access, and more labor. Pricing below assumes standard single-story access.
| home size | St. Louis 2026 range |
|---|---|
| 1 bath / ~1,000 sq ft | $3,200 – $5,650 |
| 2 bath / ~1,500 sq ft | $4,000 – $7,100 |
| 3 bath / ~2,000 sq ft | $4,950 – $9,100 |
| 4+ bath / 2,500+ sq ft | $6,150 – $12,050 |
National size ranges localized to St. Louis labor and climate.
Whole House Repipe cost by type in St. Louis
| PEX | $3,600 – $7,100 |
| CPVC | $4,150 – $8,100 |
| Copper | $6,150 – $14,950 |
Adjusted to St. Louis from national type-level ranges.
Whole House Repipe cost by efficiency in St. Louis
The pipe material drives both price and longevity. PEX is flexible, fast to run, and the cheapest to install; rigid copper costs more in material and labor but is the long-haul standard many buyers prefer.
| PEX (cross-linked polyethylene)Cheapest to install; flexible, freeze-tolerant | $3,200 – $6,150 |
| CPVCMid-cost rigid plastic; common in hot-water lines | $3,700 – $7,100 |
| Copper (rigid)Highest cost; long lifespan, resale appeal | $5,150 – $12,050 |
Labor vs. materials in St. Louis
Install crew, removal, permit & startup — the part St. Louis rates move most.
Equipment & materials — priced closer to the national level.
Split based on a typical $5,850 St. Louis project; your mix varies with scope.
How we estimate it
| National range | $3,400 – $8,000 |
| St. Louis labor adjustment | ×0.98 |
| mixed climate factor | ×1 |
| Local permit | +$250 |
| St. Louis estimate | $3,600 – $8,100 |
Promo prices vs. the real cost
The number that gets you a plumber in the door isn't the number for the job — those are two different budgets:
- Camera inspection$100–$350 (sometimes waived)
- Service / diagnostic call$75–$200
- "Free" estimate on big jobs$0 — it's a sales visit
Additional whole-house repipe costs to budget for
Treat them as possibilities, not certainties — the ones that reach your quote follow your property's age and setup.
| Drywall & wall/ceiling patch + repaintCrews open walls to reach pipes; finishing is often separate | $500 – $3,000 |
| Permit & inspection | $100 – $500 |
| Move out / hotel during workWhole-house repipes can take 2–5 days with water off | $0 – $1,000 |
| Replace shutoff valves & supply lines | $150 – $600 |
| Slab access / concrete cut (slab homes)Only if lines run under a concrete slab | $1,000 – $4,000 |
Typical national add-on ranges; confirm locally during your quote.
What's included
- Fixture reconnections
- Basic drywall patching and permit
- New PEX or copper supply lines
- Removal of accessible old piping
What affects the cost
- Slab vs crawlspace/basement access
- Home size and number of bathrooms
- PEX vs copper
- Wall opening and patching needed
Ways to save on whole-house repipe in St. Louis
- PEX costs less than copper and installs faster
- Get multiple licensed-plumber bids
- Repipe during a remodel to share wall access
- Act before a leak causes water damage
How long does whole-house repipe last in St. Louis?
PEX and CPVC last ~40–50+ years; copper commonly reaches 50–70+ years. A repipe is essentially a once-in-a-lifetime job.
Repiped supply lines need almost no upkeep; budget only for the occasional shutoff-valve or fixture check.
Signs you need whole-house repipe in St. Louis
- Chronic low water pressure throughout the house
- Rusty, brown, or metallic-tasting water (corroding pipes)
- Frequent or repeated pinhole leaks and pipe repairs
- Old galvanized steel, polybutylene, or lead supply pipes
- Banging, knocking, or whistling pipes (water hammer / corrosion)
- Visible corrosion, flaking, or green stains on exposed pipe
- The home is 50+ years old on its original plumbing
Repair or replace in St. Louis?
Repair if…
- A single, accessible leak in otherwise sound modern pipe (PEX/copper)
- The rest of the system is under ~25 years old and leak-free
- The damaged section is short and easy to isolate
Replace if…
- Pipes are galvanized steel, polybutylene, or lead
- Leaks keep recurring in different spots (systemic corrosion)
- Water pressure and water quality are both declining
- You're already gutting walls for a remodel (do it once)
Cheapest time for whole-house repipe in St. Louis
True emergencies pay full rate. But planned projects — a repipe or sewer-line replacement — can be scheduled in a slower month for slightly better pricing and more attentive crews.
Why whole-house repipe quotes vary — and how to compare them fairly
A wide spread between bids rarely means someone is overcharging; it usually means they priced different work. Below is what moves the number and how to line the quotes up.
Why a quote looks high (or low)
- Permits, inspection and surface/landscape restoration may be excluded.
- Pipe material (PEX vs. copper) changes both cost and longevity.
- Trenchless vs. traditional dig is a major price difference.
Get an apples-to-apples bid
- Ask whether trenchless or dig fits your situation and why.
- Compare pipe material on equal terms.
- Require a camera inspection so the scope is confirmed before work.
- Confirm permits, inspection and restoration are included.
Questions to ask St. Louis Plumbing pros
You can't judge bids side by side unless they cover the same ground; run through these with every pro on your list.
- 1Trenchless vs. traditional dig — which fits my situation and why?
- 2Is a camera inspection included so we confirm the scope before digging?
- 3Are permits, inspection, and surface/landscape restoration included?
- 4What pipe material are you using (PEX vs. copper) and why?
- 5Who is responsible for the city-owned portion of the line?
Whole House Repipe in St. Louis
How much does whole-house repipe cost in St. Louis, MO?
Budgeting for whole-house repipe? In St. Louis, 2026 prices land between $3,600 and $8,100, and about $5,850 is the typical outcome. That range already accounts for St. Louis's labor rates, its mixed climate and local permit costs.
Is whole-house repipe more expensive in St. Louis than average?
Put St. Louis next to the national picture and it lands about 3% higher than the national average; the labor index of 0.98 explains the bulk of it. and the local Plumbing permit costs about $250.
Do I need a permit for whole-house repipe in St. Louis?
Most St. Louis jurisdictions require a Plumbing permit for this work. Budget roughly $250 for the permit; it is already included in the estimate above.
What affects whole-house repipe cost the most?
Replacing a home's water supply piping — typically swapping old galvanized or failing pipe for PEX or copper. Where two homes diverge is in the details below. Expect equipment/material grade, home size and complexity, local labor rates and the mixed climate zone to matter most here.
How do you budget a major plumbing job?
There's no fixed price for a repipe or sewer job until you know the method and what's below the yard. Our editors on how to think about the scope.
The method case
Trenchless repair costs more per foot but saves your driveway, landscaping and the restoration bill. Traditional dig is cheaper upfront only if there's little to tear up and rebuild.
The material case
In freeze-prone regions PEX has the advantage: cheaper, quicker to run, and forgiving when temperatures drop. Copper asks for more up front but outlasts it and can nudge resale with certain buyers. The tiebreaker is your weather and your timeline in the house, not a blanket rule.
The diagnosis-first case
Never budget a sewer or repipe job from a guess. A camera inspection confirms the real scope and stops you paying for work you don't need — or being blindsided by work you do.
Scope, not brand, is what sets a plumbing price. Confirm it with a camera inspection, compare trenchless against the full cost of a dig — landscaping included — and match pipe material to your climate.
Editorial analysis by Serhat Özçelik, reviewed by Costadia Editorial. These are our own cost perspectives, not third-party endorsements.
How we calculated this estimate
We start with 2026 national whole-house repipe ranges compiled from contractor-pricing sources (Angi, HomeGuide, Fixr and EnergySage averages), then localize them to St. Louis using the BEA Regional Price Parity labor index (×0.98 here), the IECC mixed-climate factor (×1) and a typical local permit fee (≈$250). Federal incentive details reference the IRS Inflation Reduction Act (25C/25D) and DSIRE.
This is a planning estimate, not a quote.Actual prices vary with your home's condition, equipment grade and contractor — always confirm with licensed local pros before budgeting.
References & data sources
Our St. Louis whole-house repipe estimate is built from these primary, mostly government sources — not a single aggregator.
- Occupational Employment & Wage Statistics (metro wages) — U.S. Bureau of Labor Statistics.Metro-level trade wages behind each city's labor index.
- Regional Price Parities (state & metro) — U.S. Bureau of Economic Analysis.Regional price levels used where metro wage data is unavailable.
- IECC Climate Zones — U.S. DOE — Building Energy Codes Program.Climate-zone factors applied to weather-sensitive projects.
- Home Energy Tax Credits (25C / 25D) — Internal Revenue Service.Federal rebate and tax-credit figures for eligible upgrades.
- Database of State Incentives for Renewables & Efficiency — DSIRE — NC State University.State and utility incentive programs by ZIP code.
Homeowners in St. Louis often pair this with
A whole-house repipe rarely happens in isolation — these projects commonly come up alongside it.
Other projects in St. Louis
Browse local 2026 costs for every home project in St. Louis, MO.