Plumbing · Edmonds, WA
How much does whole-house repipe cost in Edmonds, WA? (2026)
In Edmonds, whole-house repipe runs $4,350–$9,800, with most paying around $7,100 — about 25% above the national average. Replacing a home's water supply piping — typically swapping old galvanized or failing pipe for PEX or copper.
Updated June 2026 · Localized estimate, not a quote
Most homeowners pay around $7,100
- Typical cost
- $7,100
- Labor vs US
- +14%
- Climate
- Mixed
- Local permit
- $275
Refine your estimate
Tune it to your home to narrow the whole-house repipe range.
Key takeaways for Edmonds
- Most Edmonds homeowners land around $7,100 for whole-house repipe, within a $4,350–$9,800 range that sits about 25% above the national average.
- Local labor in Edmonds is +14% relative to the national average, which is what pushes this estimate away from the countrywide number.
- The estimate already covers the Plumbing permit — roughly $275 in Edmonds.
- Count on 50–100 years from a solid install; timing the next job yourself avoids the emergency premium.
- Off-peak winter for planned work is the low-price window — about Around 5% under peak rates.
What goes into the price in Edmonds
A typical Edmonds whole-house repipe of $7,100 breaks down roughly like this — materials priced near the national level, labor set by local rates.
| Line item | Edmonds 2026 range |
|---|---|
| Materials & equipmentHardware and supplies for the job; national pricing applies almost everywhere you go. | $1,650 – $3,800 |
| Labor & installationInstall crew, removal and startup — the part local rates move most. | $2,425 – $5,725 |
| Permit & feesWhat this city's building department charges for a Plumbing permit. | $275 |
| Total installed cost | $4,350 – $9,800 |
Split from the Edmonds estimate using a 60% local-labor share; line items sum to the total.
Why whole-house repipe costs what it does in Edmonds
- Expect labor here to run 14% above the national norm (based on price levels for the Seattle-Tacoma-Bellevue metro area) — that's what raises the total.
- A Plumbing permit in Edmonds costs around $275, included above.
Whole House Repipe cost by home size in Edmonds
Repipe cost scales with how many bathrooms and fixtures the crew has to reach — more baths means more runs, more wall and ceiling access, and more labor. Pricing below assumes standard single-story access.
| home size | Edmonds 2026 range |
|---|---|
| 1 bath / ~1,000 sq ft | $3,850 – $6,850 |
| 2 bath / ~1,500 sq ft | $4,800 – $8,600 |
| 3 bath / ~2,000 sq ft | $6,000 – $11,000 |
| 4+ bath / 2,500+ sq ft | $7,400 – $14,550 |
National size ranges localized to Edmonds labor and climate.
Whole House Repipe cost by type in Edmonds
| PEX | $4,300 – $8,600 |
| CPVC | $5,050 – $9,800 |
| Copper | $7,400 – $18,150 |
Adjusted to Edmonds from national type-level ranges.
Whole House Repipe cost by efficiency in Edmonds
The pipe material drives both price and longevity. PEX is flexible, fast to run, and the cheapest to install; rigid copper costs more in material and labor but is the long-haul standard many buyers prefer.
| PEX (cross-linked polyethylene)Cheapest to install; flexible, freeze-tolerant | $3,850 – $7,400 |
| CPVCMid-cost rigid plastic; common in hot-water lines | $4,450 – $8,600 |
| Copper (rigid)Highest cost; long lifespan, resale appeal | $6,250 – $14,550 |
Labor vs. materials in Edmonds
Install crew, removal, permit & startup — the part Edmonds rates move most.
Equipment & materials — priced closer to the national level.
Split based on a typical $7,100 Edmonds project; your mix varies with scope.
Skilled installers in the Seattle-Tacoma-Bellevue area earn about $41.1/hr (32% above the US average, per BLS metro wage data) — the local wage is what moves the labor half of your whole-house repipe cost.
How we estimate it
| National range | $3,400 – $8,000 |
| Edmonds labor adjustment | ×1.19 |
| mixed climate factor | ×1 |
| Local permit | +$275 |
| Edmonds estimate | $4,350 – $9,800 |
Promo prices vs. the real cost
A dispatch fee gets someone to your house. It has little bearing on what a repipe or sewer job actually costs:
- "Free" estimate on big jobs$0 — it's a sales visit
- Camera inspection$100–$350 (sometimes waived)
- Service / diagnostic call$75–$200
Additional whole-house repipe costs to budget for
Some of these land on the final invoice and some never surface — it comes down to your home's age, access and existing setup.
| Drywall & wall/ceiling patch + repaintCrews open walls to reach pipes; finishing is often separate | $500 – $3,000 |
| Permit & inspection | $100 – $500 |
| Move out / hotel during workWhole-house repipes can take 2–5 days with water off | $0 – $1,000 |
| Replace shutoff valves & supply lines | $150 – $600 |
| Slab access / concrete cut (slab homes)Only if lines run under a concrete slab | $1,000 – $4,000 |
Typical national add-on ranges; confirm locally during your quote.
What's included
- New PEX or copper supply lines
- Basic drywall patching and permit
- Fixture reconnections
- Removal of accessible old piping
What affects the cost
- PEX vs copper
- Wall opening and patching needed
- Home size and number of bathrooms
- Slab vs crawlspace/basement access
Ways to save on whole-house repipe in Edmonds
- Get multiple licensed-plumber bids
- PEX costs less than copper and installs faster
- Act before a leak causes water damage
- Repipe during a remodel to share wall access
How long does whole-house repipe last in Edmonds?
PEX and CPVC last ~40–50+ years; copper commonly reaches 50–70+ years. A repipe is essentially a once-in-a-lifetime job.
Repiped supply lines need almost no upkeep; budget only for the occasional shutoff-valve or fixture check.
Signs you need whole-house repipe in Edmonds
- Chronic low water pressure throughout the house
- Rusty, brown, or metallic-tasting water (corroding pipes)
- Frequent or repeated pinhole leaks and pipe repairs
- Old galvanized steel, polybutylene, or lead supply pipes
- Banging, knocking, or whistling pipes (water hammer / corrosion)
- Visible corrosion, flaking, or green stains on exposed pipe
- The home is 50+ years old on its original plumbing
Repair or replace in Edmonds?
Repair if…
- A single, accessible leak in otherwise sound modern pipe (PEX/copper)
- The rest of the system is under ~25 years old and leak-free
- The damaged section is short and easy to isolate
Replace if…
- Pipes are galvanized steel, polybutylene, or lead
- Leaks keep recurring in different spots (systemic corrosion)
- Water pressure and water quality are both declining
- You're already gutting walls for a remodel (do it once)
Cheapest time for whole-house repipe in Edmonds
True emergencies pay full rate. But planned projects — a repipe or sewer-line replacement — can be scheduled in a slower month for slightly better pricing and more attentive crews.
Why whole-house repipe quotes vary — and how to compare them fairly
Two contractors can price the same job thousands apart. Almost always it's the scope each assumed — here's what drives the gap and how to close it.
Why a quote looks high (or low)
- Scope is often unknown until a camera inspection confirms it.
- Pipe material (PEX vs. copper) changes both cost and longevity.
- Permits, inspection and surface/landscape restoration may be excluded.
Get an apples-to-apples bid
- Clarify who owns the city-side portion of the line.
- Require a camera inspection so the scope is confirmed before work.
- Confirm permits, inspection and restoration are included.
- Ask whether trenchless or dig fits your situation and why.
Questions to ask Edmonds Plumbing pros
A fair comparison starts with identical questions. Ask each contractor the following before anything gets signed.
- 1Trenchless vs. traditional dig — which fits my situation and why?
- 2Is a camera inspection included so we confirm the scope before digging?
- 3Are permits, inspection, and surface/landscape restoration included?
- 4What pipe material are you using (PEX vs. copper) and why?
- 5Who is responsible for the city-owned portion of the line?
Whole House Repipe in Edmonds
How much does whole-house repipe cost in Edmonds, WA?
Edmonds's going rate for whole-house repipe is $4,350–$9,800 in 2026, with $7,100 the number most homeowners end up paying. Strip out Edmonds's labor rates, its mixed climate and permit fees and you'd be left with a national average — this range keeps them in.
Is whole-house repipe more expensive in Edmonds than average?
Why the gap? Edmonds prices about 25% higher than the national average, and local labor — indexed at 1.19 against the US average — does most of the work., plus a local Plumbing permit running about $275.
Do I need a permit for whole-house repipe in Edmonds?
Most Edmonds jurisdictions require a Plumbing permit for this work. Budget roughly $275 for the permit; it is already included in the estimate above.
What affects whole-house repipe cost the most?
Worth knowing first: replacing a home's water supply piping — typically swapping old galvanized or failing pipe for PEX or copper. Grade of equipment and materials tops the list, followed by home size and complexity, local labor, and the mixed climate zone.
How do you budget a major plumbing job?
The price of a repipe or sewer replacement is set less by who does the work than by how it's installed and what the crew finds under the yard.
The method case
Trenchless repair costs more per foot but saves your driveway, landscaping and the restoration bill. Traditional dig is cheaper upfront only if there's little to tear up and rebuild.
The diagnosis-first case
Never budget a sewer or repipe job from a guess. A camera inspection confirms the real scope and stops you paying for work you don't need — or being blindsided by work you do.
The material case
PEX is cheaper, faster and freeze-tolerant; copper costs more but lasts longer and some buyers prefer it. Match the material to your climate and how long you'll own the home.
Scope, not brand, is what sets a plumbing price. Confirm it with a camera inspection, compare trenchless against the full cost of a dig — landscaping included — and match pipe material to your climate.
Editorial analysis by Serhat Özçelik, reviewed by Costadia Editorial. These are our own cost perspectives, not third-party endorsements.
How we calculated this estimate
We start with 2026 national whole-house repipe ranges compiled from contractor-pricing sources (Angi, HomeGuide, Fixr and EnergySage averages), then localize them to Edmonds using the BLS metro wage data labor index (×1.19 here), the IECC mixed-climate factor (×1) and a typical local permit fee (≈$275). Federal incentive details reference the IRS Inflation Reduction Act (25C/25D) and DSIRE.
This is a planning estimate, not a quote.Actual prices vary with your home's condition, equipment grade and contractor — always confirm with licensed local pros before budgeting.
References & data sources
Our Edmonds whole-house repipe estimate is built from these primary, mostly government sources — not a single aggregator.
- Occupational Employment & Wage Statistics (metro wages) — U.S. Bureau of Labor Statistics.Metro-level trade wages behind each city's labor index.
- Regional Price Parities (state & metro) — U.S. Bureau of Economic Analysis.Regional price levels used where metro wage data is unavailable.
- IECC Climate Zones — U.S. DOE — Building Energy Codes Program.Climate-zone factors applied to weather-sensitive projects.
- Home Energy Tax Credits (25C / 25D) — Internal Revenue Service.Federal rebate and tax-credit figures for eligible upgrades.
- Database of State Incentives for Renewables & Efficiency — DSIRE — NC State University.State and utility incentive programs by ZIP code.
Homeowners in Edmonds often pair this with
A whole-house repipe rarely happens in isolation — these projects commonly come up alongside it.
Other projects in Edmonds
Browse local 2026 costs for every home project in Edmonds, WA.