Spray Foam Insulation cost: Bloomington vs Plymouth (2026)
Bloomington and Plymouth are a near-perfect match on spray foam insulation cost in 2026, both landing around $4,400.
Bloomington MN
Typically around $4,400
Plymouth MN
Typically around $4,400
Bloomington vs Plymouth: full breakdown
| Factor | Bloomington | Plymouth |
|---|---|---|
| Typical 2026 cost | $4,400 | $4,400 |
| Estimated range | $1,750–$7,000 | $1,750–$7,000 |
| Labor index (vs US) | ×1.1 | ×1.1 |
| Climate zone | Cold | Cold |
| Climate factor | ×1.06 | ×1.06 |
| Local permit | None | None |
| Labor share | $2,400 | $2,400 |
| Materials/equipment | $2,000 | $2,000 |
Spray foam insulation numbers here are 2026 planning ranges, adjusted per city — useful for budgeting, not a substitute for an actual quote.
Basically a tie — focus on the contractor
The two metros are effectively a wash for spray foam insulation — pick on contractor quality and timing, not location.
Spray foam insulation by type: Bloomington vs Plymouth
Below, each spray foam insulation option is priced independently for both cities, with identical local labor, climate and permit logic applied — so the comparison holds up.
| Type | Bloomington | Plymouth |
|---|---|---|
| Open-cell | $1,750–$5,250 | $1,750–$5,250 |
| Closed-cell | $2,900–$8,150 | $2,900–$8,150 |
These are 2026 planning figures for spray foam insulation, localized to each city — not formal quotes.
Spray foam insulation by area: Bloomington vs Plymouth
Spray foam is priced by board foot (1 sq ft at 1 inch thick), which works out to about $1.50–$5 per sq ft of surface installed depending on foam type and thickness. Closed-cell costs more but adds twice the R-value per inch.
| Size | Bloomington | Plymouth |
|---|---|---|
| 500 sq ft | $1,050–$2,800 | $1,050–$2,800 |
| 1,000 sq ft | $1,750–$4,650 | $1,750–$4,650 |
| 1,500 sq ft | $2,550–$6,400 | $2,550–$6,400 |
| 2,000+ sq ft | $3,250–$7,550 | $3,250–$7,550 |
Localized 2026 planning estimates — not quotes. Each city adjusts the national spray foam insulation range for local labor, climate and permits.
What insulation pros earn in each metro
Roughly 55% of what you pay for spray foam insulation is labor, which is why local wages explain most of the price gap. The numbers below are actual metro wages for skilled installers, sourced from BLS OEWS — not guesses.
Minneapolis-St. Paul-Bloomington metro · about 18% above the US average installer wage.
Minneapolis-St. Paul-Bloomington metro · about 18% above the US average installer wage.
Source: U.S. Bureau of Labor Statistics, OEWS metro wages for HVAC installers (used as a trade-labor index).
Cheapest time for spray foam insulation in either city
Demand for insulation spikes every fall as winter approaches, pushing prices with it. Spring and summer avoid that crowd, and utility rebate pools are frequently still fresh that early in the year.
How much insulation is worth paying for?
Where an insulation budget lands depends less on square footage than on three calls — the R-value you target, whether air-sealing rides along, and which material fills the cavity.
The R-value case
The DOE publishes a target R-value for every climate zone, and there's a reason to reach it: stopping short shaves a little off install day but forfeits years of lower energy bills and steadier indoor temperatures. Under-insulating is the one shortcut here that never actually pays.
The rebate case
Insulation carries some of the strongest incentive money in remodeling, with utility and state rebates covering a real portion of the cost since the federal 25C credit expired at the end of 2025. Look up what applies on DSIRE, then schedule the work while rebate funds are still unclaimed for the year.
The air-sealing case
Insulation without air-sealing underperforms. Sealing leaks first is cheap and often delivers more comfort per dollar than thicker insulation alone — make sure it's in the scope.
Rare among home projects, insulation punishes the half-measure — the money saved by under-insulating or skipping the air-seal comes back as higher bills. Meet the DOE R-value for your zone, seal the leaks first, and use the rebates on the table.
Bloomington vs Plymouth
Is spray foam insulation cheaper in Bloomington or Plymouth?
Not really — both cities land at almost the same number for spray foam insulation, around $4,400 each.
Why does spray foam insulation cost more in Plymouth than Bloomington?
Plymouth's higher labor index (1.1 vs 1.1 in Bloomington) is the biggest factor, with the cold/cold climate split playing a smaller role.
How much is spray foam insulation in Bloomington, MN?
spray foam insulation in Bloomington runs $1,750–$7,000 as of 2026 — most jobs land near $4,400.
Do insulation pros really charge more in one city?
It's not a myth — BLS data puts installer wages at about $36.7/hr in the Minneapolis-St. Paul-Bloomington area and $36.7/hr in Minneapolis-St. Paul-Bloomington. Given labor is around 55% of a spray foam insulation job's cost, that gap explains most of the price spread.
When is the cheapest time to buy spray foam insulation — and does it differ by city?
It doesn't vary by location — Spring and summer is the discount window in both Bloomington and Plymouth (roughly 5–10% off), while the pre-winter fall rush tends to be the most expensive in either city.
Should I choose where to live based on spray foam insulation cost?
No — the cost is essentially identical between Bloomington and Plymouth. Base the decision on the things that actually vary: contractor reputation, scope, equipment tier and timing.
Compare spray foam insulation in other cities
Updated June 2026 · By Serhat Özçelik