Metal Roof Installation cost: Carrollton vs Dallas (2026)
Carrollton and Dallas are a near-perfect match on metal roof installation cost in 2026, both landing around $21,850.
Carrollton TX
Typically around $21,850
Dallas TX
Typically around $21,850
Carrollton vs Dallas: full breakdown
| Factor | Carrollton | Dallas |
|---|---|---|
| Typical 2026 cost | $21,850 | $21,850 |
| Estimated range | $13,300–$30,350 | $13,300–$30,350 |
| Labor index (vs US) | ×0.97 | ×0.97 |
| Climate zone | Hot | Hot |
| Climate factor | ×1.03 | ×1.03 |
| Local permit | $300 | $300 |
| Labor share | $13,100 | $13,100 |
| Materials/equipment | $8,750 | $8,750 |
Localized 2026 planning estimates — not quotes. Each city adjusts the national metal roof installation range for local labor, climate and permits.
No real cost edge either way
With no real price gap on metal roof installation, the choice comes down to contractor quality and timing, not which city you're in.
Metal roof installation by type: Carrollton vs Dallas
We localize each metal roof installation type separately for both metros, applying the same labor, climate and permit adjustments each time, so you're comparing like for like.
| Type | Carrollton | Dallas |
|---|---|---|
| Corrugated steel (exposed fastener) | $9,300–$18,300 | $9,300–$18,300 |
| Standing-seam steel | $18,300–$35,350 | $18,300–$35,350 |
| Aluminum | $14,300–$28,350 | $14,300–$28,350 |
| Copper | $30,350–$60,350 | $30,350–$60,350 |
| Zinc | $28,350–$55,350 | $28,350–$55,350 |
These are 2026 planning figures for metal roof installation, localized to each city — not formal quotes.
Metal roof installation by roof size: Carrollton vs Dallas
Metal roofing is priced per square (100 sq ft) and costs roughly $6–$14 per sq ft installed — two to three times asphalt, but it lasts decades longer. Standing-seam costs more than exposed-fastener panels.
| Size | Carrollton | Dallas |
|---|---|---|
| 1,000 sq ft (10 squares) | $8,300–$16,300 | $8,300–$16,300 |
| 1,500 sq ft (15 squares) | $11,300–$23,300 | $11,300–$23,300 |
| 2,000 sq ft (20 squares) | $13,300–$30,350 | $13,300–$30,350 |
| 2,500 sq ft (25 squares) | $16,300–$36,350 | $16,300–$36,350 |
| 3,000+ sq ft (30 squares) | $19,300–$42,350 | $19,300–$42,350 |
Metal roof installation numbers here are 2026 planning ranges, adjusted per city — useful for budgeting, not a substitute for an actual quote.
What roofing pros earn in each metro
About 60% of a metal roof installation bill goes to labor, so wage differences between these two metros matter more than almost anything else. These are real, government-sourced (BLS OEWS) installer wages, not estimates.
Dallas-Fort Worth-Arlington metro · about 5% below the US average installer wage.
Dallas-Fort Worth-Arlington metro · about 5% below the US average installer wage.
Source: U.S. Bureau of Labor Statistics, OEWS metro wages for HVAC installers (used as a trade-labor index).
Cheapest time for metal roof installation in either city
Shingles seal properly only in warm, dry conditions, which is exactly when everyone else wants a new roof too — especially right after a summer hailstorm. Lock in a late-fall or winter booking for a spring install and you skip that rush.
Where does a smart roofing budget go in 2026?
The real cost of a roof comes down to three decisions: tear-off or overlay, which shingle tier, and what condition the decking is in. Our editors weigh in.
The do-it-right case
Skipping the tear-off means burying whatever's failing underneath, and a second layer bakes the shingles from below until they curl early. Doing it properly means stripping to the deck, then paying for real underlayment, flashing and airflow — the work that sets how long the roof lasts, not just how it looks the first week.
The value case
Architectural shingles sit between bargain 3-tab and premium metal or tile, and for most houses that middle ground is exactly right. They carry longer wind and wear ratings than 3-tab for a small step up in price, without the four-figure jump metal or tile demands.
The risk case
Budget for the unknown: rotten decking found at tear-off is the most common surprise. Get the per-sheet repair rate in writing up front so a "cheap" bid doesn't balloon mid-job.
Judge a roofing bid on its scope, not its bottom line — a genuine tear-off, a documented per-sheet deck rate, and a mid-grade architectural shingle. Those three close the gaps that let a low storm-season number balloon over the years.
Carrollton vs Dallas
Is metal roof installation cheaper in Carrollton or Dallas?
Practically identical — expect around $21,850 for metal roof installation whichever city you're in.
Why does metal roof installation cost more in Dallas than Carrollton?
The main driver is local labor rates: Dallas's labor index is 0.97 versus 0.97 in Carrollton. Climate zone (hot vs hot) also shift the total.
How much is metal roof installation in Carrollton, TX?
In Carrollton, metal roof installation typically runs $13,300–$30,350 in 2026, with most homeowners paying around $21,850.
Do roofing pros really charge more in one city?
They do, and the BLS wage data confirms it: installers earn about $29.7/hr around Dallas-Fort Worth-Arlington versus $29.7/hr near Dallas-Fort Worth-Arlington. With labor making up about 60% of a metal roof installation job, that difference carries straight through to the final price.
When is the cheapest time to buy metal roof installation — and does it differ by city?
No, the seasonal pattern is the same in Carrollton and Dallas: book during Late spring to early fall (dry, 45–85°F) for about 5–10% in savings. Mid-winter and the post-storm rush is the priciest stretch in both cities, mostly due to emergency replacements.
Should I choose where to live based on metal roof installation cost?
Not on this basis — Carrollton and Dallas cost about the same. Weigh contractor quality, scope, equipment tier and timing instead.
Compare metal roof installation in other cities
Updated June 2026 · By Serhat Özçelik