Metal Roof Installation cost: Bloomington vs Maple Grove (2026)
Metal roof installation costs about the same in Bloomington and Maple Grove in 2026 — roughly $25,050 in each.
Bloomington MN
Typically around $25,050
Maple Grove MN
Typically around $25,050
Bloomington vs Maple Grove: full breakdown
| Factor | Bloomington | Maple Grove |
|---|---|---|
| Typical 2026 cost | $25,050 | $25,050 |
| Estimated range | $15,250–$34,850 | $15,250–$34,850 |
| Labor index (vs US) | ×1.11 | ×1.11 |
| Climate zone | Cold | Cold |
| Climate factor | ×1.04 | ×1.04 |
| Local permit | $300 | $300 |
| Labor share | $15,050 | $15,050 |
| Materials/equipment | $10,000 | $10,000 |
Metal roof installation numbers here are 2026 planning ranges, adjusted per city — useful for budgeting, not a substitute for an actual quote.
No real cost edge either way
Neither metro has a cost edge on metal roof installation — spend your decision-making energy on the contractor, not the location.
Metal roof installation by type: Bloomington vs Maple Grove
We localize each metal roof installation type separately for both metros, applying the same labor, climate and permit adjustments each time, so you're comparing like for like.
| Type | Bloomington | Maple Grove |
|---|---|---|
| Corrugated steel (exposed fastener) | $10,650–$21,000 | $10,650–$21,000 |
| Standing-seam steel | $21,000–$40,600 | $21,000–$40,600 |
| Aluminum | $16,400–$32,550 | $16,400–$32,550 |
| Copper | $34,850–$69,350 | $34,850–$69,350 |
| Zinc | $32,550–$63,600 | $32,550–$63,600 |
These are 2026 planning figures for metal roof installation, localized to each city — not formal quotes.
Metal roof installation by roof size: Bloomington vs Maple Grove
Metal roofing is priced per square (100 sq ft) and costs roughly $6–$14 per sq ft installed — two to three times asphalt, but it lasts decades longer. Standing-seam costs more than exposed-fastener panels.
| Size | Bloomington | Maple Grove |
|---|---|---|
| 1,000 sq ft (10 squares) | $9,500–$18,700 | $9,500–$18,700 |
| 1,500 sq ft (15 squares) | $12,950–$26,750 | $12,950–$26,750 |
| 2,000 sq ft (20 squares) | $15,250–$34,850 | $15,250–$34,850 |
| 2,500 sq ft (25 squares) | $18,700–$41,750 | $18,700–$41,750 |
| 3,000+ sq ft (30 squares) | $22,150–$48,650 | $22,150–$48,650 |
Localized 2026 planning estimates — not quotes. Each city adjusts the national metal roof installation range for local labor, climate and permits.
What roofing pros earn in each metro
About 60% of a metal roof installation bill goes to labor, so wage differences between these two metros matter more than almost anything else. These are real, government-sourced (BLS OEWS) installer wages, not estimates.
Minneapolis-St. Paul-Bloomington metro · about 18% above the US average installer wage.
Minneapolis-St. Paul-Bloomington metro · about 18% above the US average installer wage.
Source: U.S. Bureau of Labor Statistics, OEWS metro wages for HVAC installers (used as a trade-labor index).
Cheapest time for metal roof installation in either city
Shingles seal properly only in warm, dry conditions, which is exactly when everyone else wants a new roof too — especially right after a summer hailstorm. Lock in a late-fall or winter booking for a spring install and you skip that rush.
Where does a smart roofing budget go in 2026?
Roofing budgets swing on decisions most homeowners don't think to ask about — overlay vs. tear-off, shingle tier, deck condition. Our editors break down each one.
The risk case
Budget for the unknown: rotten decking found at tear-off is the most common surprise. Get the per-sheet repair rate in writing up front so a "cheap" bid doesn't balloon mid-job.
The value case
For a typical home, the architectural shingle is the default that makes sense. It outlasts 3-tab by a wide margin at a modest premium, and it spares you the cost of metal or tile that most roofs never need to justify.
The do-it-right case
Pay for a full tear-off and quality underlayment, flashing and ventilation. An overlay saves money today but traps heat, voids some warranties and costs more at the next replacement.
Three habits keep a roof from costing more than it should: strip to the deck, choose an architectural shingle, and get the decking-repair rate on paper before the tear-off begins. Storm season tends to produce the lowest bids and the shortest-lived roofs.
Bloomington vs Maple Grove
Is metal roof installation cheaper in Bloomington or Maple Grove?
Not really — both cities land at almost the same number for metal roof installation, around $25,050 each.
Why does metal roof installation cost more in Maple Grove than Bloomington?
It comes down to labor: Maple Grove indexes at 1.11 against Bloomington's 1.11. The cold-vs-cold climate difference adds to the gap.
How much is metal roof installation in Bloomington, MN?
Expect to pay $15,250 to $34,850 for metal roof installation in Bloomington in 2026, averaging around $25,050.
Do roofing pros really charge more in one city?
Real wage data backs this up — skilled installers earn roughly $36.7/hr in Minneapolis-St. Paul-Bloomington compared with $36.7/hr in Minneapolis-St. Paul-Bloomington (BLS OEWS). Labor is about 60% of a metal roof installation job, so that wage gap is what mostly drives the price difference.
When is the cheapest time to buy metal roof installation — and does it differ by city?
It doesn't vary by location — Late spring to early fall (dry, 45–85°F) is the discount window in both Bloomington and Maple Grove (roughly 5–10% off), while mid-winter and the post-storm rush tends to be the most expensive in either city.
Should I choose where to live based on metal roof installation cost?
There's no cost argument here between Bloomington and Maple Grove — they're a wash. Focus on contractor reputation, project scope, equipment tier and timing.
Compare metal roof installation in other cities
Updated June 2026 · By Serhat Özçelik